Isn't that a legacy command from the NM-HD-FARM module and IOS's before, something like 12.2 or 12.1 or maybe earlier. Can't remember.
________________________________ From: ccie_voice-boun...@onlinestudylist.com [ccie_voice-boun...@onlinestudylist.com] On Behalf Of Kumar, Narinder [narinder.ku...@uxcg.com.au] Sent: Saturday, October 03, 2009 10:57 AM To: ABIOLA ADEFILA; manishankar pandey Cc: OSL Group Subject: Re: [OSL | CCIE_Voice] conference bridge regisration In your config . voice-card 0 no dspfarm---------Why you have no dspfarm ??? change it to dspfarm , reset your conf bridge. From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of ABIOLA ADEFILA Sent: Sunday, 4 October 2009 12:06 AM To: manishankar pandey Cc: OSL Group Subject: Re: [OSL | CCIE_Voice] conference bridge regisration Hello, i checked my config the bind was there but still the conference bridge is not registering i did no sccp sccp the command is as shown below hostname BR1-RTR ! boot-start-marker warm-reboot boot-end-marker ! logging message-counter syslog ! no aaa new-model memory-size iomem 20 network-clock-participate wic 0 network-clock-select 1 T1 0/0/0 ! dot11 syslog ip source-route ! ! ip cef ! ! ip domain name proctorlabs.com<http://proctorlabs.com> no ipv6 cef ! multilink bundle-name authenticated ! ! isdn switch-type primary-ni ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! voice-card 0 no dspfarm dsp services dspfarm ! ! ! ! ! archive log config hidekeys ! ! ! ! ! controller T1 0/0/0 framing esf linecode b8zs pri-group timeslots 1-3,24 service mgcp ! controller T1 0/0/1 framing esf linecode b8zs channel-group 0 timeslots 1-24 ! ! ! ! ! interface Loopback0 ip address 10.10.110.2 255.255.255.255 ip ospf network point-to-point ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/0/0:23 no ip address encapsulation hdlc isdn switch-type primary-ni isdn incoming-voice voice isdn bind-l3 ccm-manager isdn bchan-number-order ascending isdn outgoing display-ie no cdp enable ! interface Serial0/0/1:0 no ip address encapsulation frame-relay IETF frame-relay lmi-type ansi ! interface Serial0/0/1:0.1 point-to-point ip address 10.10.111.2 255.255.255.0 ip ospf mtu-ignore snmp trap link-status frame-relay interface-dlci 101 ! interface FastEthernet1/0 switchport trunk native vlan 130 switchport mode trunk switchport voice vlan 240 ! interface FastEthernet1/1 ! interface FastEthernet1/2 ! interface FastEthernet1/3 ! interface FastEthernet1/4 ! interface FastEthernet1/5 ! interface FastEthernet1/6 ! interface FastEthernet1/7 ! interface FastEthernet1/8 switchport trunk native vlan 130 switchport mode trunk switchport voice vlan 240 ! interface FastEthernet1/9 ! interface FastEthernet1/10 ! interface FastEthernet1/11 ! interface FastEthernet1/12 ! interface FastEthernet1/13 ! interface FastEthernet1/14 ! interface FastEthernet1/15 ! interface Vlan1 no ip address ! interface Vlan130 ip address 10.10.101.1 255.255.255.0 ! interface Vlan240 ip address 10.10.201.1 255.255.255.0 ip helper-address 10.10.210.10 ! router ospf 1 router-id 10.10.101.1 log-adjacency-changes network 10.10.0.0 0.0.255.255 area 0 ! no ip forward-protocol nd no ip http server no ip http secure-server ! ! ! ! ! ! ! ! ! ! control-plane ! rmon event 33333 log trap AutoQoS description "AutoQoS SNMP traps for Voice Drops" owner AutoQoS ! ! voice-port 0/0/0:23 ! ccm-manager switchback immediate ccm-manager fallback-mgcp ccm-manager redundant-host 10.10.210.10 ccm-manager mgcp ! mgcp mgcp call-agent 10.10.210.11 service-type mgcp version 0.1 mgcp dtmf-relay voip codec all mode out-of-band mgcp bind control source-interface Loopback0 mgcp bind media source-interface Loopback0 ! mgcp profile default ! sccp local Vlan240 sccp ccm 10.10.110.10 identifier 2 version 5.0.1 sccp ccm 10.10.110.11 identifier 1 version 5.0.1 sccp ! sccp ccm group 1 bind interface Vlan240 associate ccm 1 priority 1 associate ccm 2 priority 2 associate profile 2 register br-cfb associate profile 1 register br1-xcoder ! dspfarm profile 1 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 maximum sessions 1 associate application SCCP shutdown ! dspfarm profile 2 conference codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 codec g729br8 maximum sessions 1 associate application SCCP ! ! ! ! ! gatekeeper shutdown ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 exec-timeout 0 0 logging synchronous no login length 0 transport preferred none transport input telnet line vty 5 15 exec-timeout 0 0 privilege level 15 logging synchronous no login transport preferred none transport input telnet ! scheduler allocate 20000 1000 end BR1-RTR(config)# On Sat, Oct 3, 2009 at 8:49 AM, ABIOLA ADEFILA <adefilabi...@gmail.com<mailto:adefilabi...@gmail.com>> wrote: Hello, I think i did not put the bind command, will fix it and get back to you Regards On Sat, Oct 3, 2009 at 2:59 AM, manishankar pandey <manishankar...@yahoo.com<mailto:manishankar...@yahoo.com>> wrote: Pl check that the name used on the Router config and on the CCM. Both needs to match. Yes, it wil be interesting to see your config on router. Regards --- On Sat, 10/3/09, Sivakumar Mahalingam <sima...@gmail.com<mailto:sima...@gmail.com>> wrote: From: Sivakumar Mahalingam <sima...@gmail.com<mailto:sima...@gmail.com>> Subject: Re: [OSL | CCIE_Voice] conference bridge regisration To: "Cristobal Priego" <cristobalpri...@gmail.com<mailto:cristobalpri...@gmail.com>> Cc: "OSL Group" <ccie_voice@onlinestudylist.com<mailto:ccie_voice@onlinestudylist.com>> Date: Saturday, October 3, 2009, 7:18 AM Hi, Can you post your SCCP configuration on the router ??? Regards, Simah78 On Fri, Oct 2, 2009 at 9:22 PM, Cristobal Priego <cristobalpri...@gmail.com<http://mc/compose?to=cristobalpri...@gmail.com>> wrote: did you configure the bind command under the group ? 2009/10/2 ABIOLA ADEFILA <adefilabi...@gmail.com<http://mc/compose?to=adefilabi...@gmail.com>> Hello, I have configured the conference bridge on the router sccp is up and the dsp is up too it does not register to the callmanager, does any one have an idea why this is egards _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com<http://www.ipexpert.com/> _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com<http://www.ipexpert.com/> -----Inline Attachment Follows----- _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com<http://www.ipexpert.com/> _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com<http://www.ipexpert.com/> ________________________________ CONFIDENTIALITY - The information contained in this electronic mail message is confidential and is intended solely for the addressee(s). If you are not an authorised recipient of this message please contact UXC Getronics Australia immediately by reply email and destroy/delete this message from your computer. Any unauthorised form of reproduction of this message, or part thereof, is strictly prohibited. DISCLAIMER - Unless specifically indicated otherwise, the views and opinions expressed in this email are those of the sender and not UXC Getronics Australia. While we endeavour to protect our network from computer viruses, UXC Getronics Australia does not warrant that this email or any attachments are free of viruses or any other defects or errors. It is the duty of the recipient to virus scan and otherwise test any information contained in this email before loading onto any computer system.
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
