This is an interesting scenario. Is this realistic - back-hauling a CME PRI to CUCM?
On Sun, Oct 4, 2009 at 12:13 AM, Andrew Lythgoe <lythgo...@gmail.com> wrote: > Hi Erwan, > > In your config for BR2 I see you have: > > controller E1 0/2 > clock source internal > pri-group timeslots 1-3,16 service mgcp > > Howevever I don't see you binding this to CCM which is required for > MGCP, for example: > > interface Serial0/2:15 > isdn bind-l3 ccm-manager > > If this is a back-to-back E1 connection then you will need to specify > the network side (only configure this on one side of the E1, not both): > > example: > > interface Serial2/0/1:15 > isdn protocol-emulate network > > Once completed the above and if problem is still experienced, please > send the following from both routers: > 1. show run > 2. show version > 3. show controllers > 4. show isdn status > 5. debug isdn q921 > > Regards, > Andrew > > > > > > > > > anil batra wrote: > > Can you let us know your outputs for .. > > > > 1. debug isdn q921 > > > > 2. sh isdn status > > > > --- On *Sun, 10/4/09, Erwan Erwan /<e_er...@yahoo.com>/* wrote: > > > > > > From: Erwan Erwan <e_er...@yahoo.com> > > Subject: [OSL | CCIE_Voice] BR-2 E1 as MGCP gateway > > To: ccie_voice@onlinestudylist.com > > Date: Sunday, October 4, 2009, 4:32 AM > > > > hi, > > > > I tried to run BR-2 E1 as MGCP gateway, but can't bring the* > > isdn up , *any advice appreciated. tks > > > > Here is config > > --------------------- > > *BR-2* > > controller E1 1/0/0 > > pri-group timeslots 1-3,16 service mgcp > > ! > > interface Serial1/0/0:15 > > no ip address > > encapsulation hdlc > > isdn switch-type primary-net5 > > isdn incoming-voice voice > > isdn bind-l3 ccm-manager > > no cdp enable > > !voice-port 1/0/0:15 > > ! > > ccm-manager fallback-mgcp > > ccm-manager redundant-host 177.1.10.20 > > ccm-manager mgcp > > ccm-manager fax protocol cisco > > ccm-manager music-on-hold > > ! > > mgcp > > mgcp call-agent 177.1.10.10 service-type mgcp version 0.1 > > mgcp fax t38 ecm > > mgcp bind control source-interface FastEthernet0/0.11 > > mgcp bind media source-interface FastEthernet0/0.11 > > ! > > mgcp profile default > > ! > > dial-peer voice 2 pots > > incoming called-number . > > direct-inward-dial > > ! > > dial-peer voice 1 pots > > service mgcp > > port 1/0/0:15 > > ! > > > > ** > > *PSTN* > > -------- > > interface Serial0/2:15 > > no ip address > > encapsulation hdlc > > isdn switch-type primary-net5 > > isdn incoming-voice voice > > isdn bchan-number-order ascending > > no cdp enable > > ! > > dial-peer voice 200 pots > > description == BR2 232Y3YXXXX > > destination-pattern ^44232131.... > > port 0/2:15 > > forward-digits 8 > > ! > > controller E1 0/2 > > clock source internal > > pri-group timeslots 1-3,16 service mgcp > > ! > > > > > > > > -----Inline Attachment Follows----- > > > > _______________________________________________ > > For more information regarding industry leading CCIE Lab training, > > please visit www.ipexpert.com > > > > > > ------------------------------------------------------------------------ > > > > _______________________________________________ > > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > -- -Shikamaru
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com