Hello, it work ok now
I was using the wrong ip address on the unity connection all the while Thanks On Fri, Mar 12, 2010 at 8:30 AM, Flemming Ortvald <f...@netdesign.dk> wrote: > Unity connection can do both g729 and g711, you can use “voice class > codec” on “voice register dn” to expand codec support for sip. > > > > Med venlig hilsen > > Flemming Ortvald > Network System Eng. > NetDesign A/S > +45 4435 8346 > > Tænk på miljøet inden udskrivning af denne e-post og tilknyttede > vedhæftninger > > > *From:* Omotayo [mailto:adefilabi...@gmail.com] > *Sent:* 11 March, 2010 20:58 > *To:* Flemming Ortvald > > *Subject:* Re: [OSL | CCIE_Voice] UC and cme sip integration > > > > > Hello, > > > > I have to configure a transcoder on the br2 router? > > > > Unity connection support g729 only? > > > > Rgd > > On Thu, Mar 11, 2010 at 8:24 PM, Flemming Ortvald <f...@netdesign.dk> wrote: > > You will need a transcoder or chnage the sip endpoints to support g.711, > natively it only supports g.729 > > > > Best regards > > Flemming Ortvald > Network System Eng. > NetDesign A/S > +45 4435 8346 > > Tænk på miljøet inden udskrivning af denne e-post og tilknyttede > vedhæftninger > > > *From:* ccie_voice-boun...@onlinestudylist.com [mailto: > ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *Omotayo > *Sent:* 11 March, 2010 20:07 > *To:* OSL Group > *Subject:* Re: [OSL | CCIE_Voice] UC and cme sip integration > > > > Hello all, > > > > As anyone been able to get the SIP integration between Unity Connection and > Cme to work? I followed the Proctorlabs Guide > > > > I posted this sometime lat week and revised as advised but keep getting a > reorder tone( Number Unknown) when the message button is pressed > > Below is the relevant configuration > > > > voice service voip > allow-connections h323 to h323 > allow-connections h323 to sip > allow-connections sip to h323 > allow-connections sip to sip > no supplementary-service sip moved-temporarily > no supplementary-service sip refer > sip > bind control source-interface Loopback0 > bind media source-interface Loopback0 > registrar server expires max 600 min 60 > > > > > > > > voice register global > mode cme > source-address 10.10.110.3 port 5060 > max-dn 3 > max-pool 6 > authenticate register > mwi reg-e164 > voicemail 3600 > tftp-path flash: > create profile sync 0006855418337003 > ! > voice register dn 1 > number 3002 > call-forward b2bua busy 3600 > call-forward b2bua mailbox 3002 > call-forward b2bua noan 3600 timeout 12 > name br2 phone 2 > no-reg > label br2 phone 2 > mwi > ! > voice register dn 2 > number 3003 > call-forward b2bua busy 3600 > call-forward b2bua mailbox 3003 > call-forward b2bua noan 3600 timeout 12 > name br2 phone 3 > no-reg > label br2 phone 3 > mwi > ! > voice register pool 1 > id mac 1111.1111.1111 > type 7941 > number 1 dn 1 > dtmf-relay rtp-nte > username 3002 password cisco > ! > voice register pool 2 > id mac 001F.6C7E.D6FE > type 7941 > number 1 dn 2 > dtmf-relay rtp-nte > username 3003 password cisco > > > > > > dial-peer voice 200 voip > max-conn 1 > destination-pattern 3600 > session protocol sipv2 > session target ipv4:10.10.210.13 > dtmf-relay rtp-nte > codec g711ulaw > ! > ! > > > > telephony-service > no auto-reg-ephone > em logout 0:0 0:0 0:0 > max-ephones 8 > max-dn 8 > ip source-address 10.10.202.1 port 2000 > voicemail 3600 > mwi relay > max-conferences 8 gain -6 > transfer-system full-consult > transfer-pattern .T > create cnf-files version-stamp 7960 Mar 10 2010 15:22:39 > ! > ! > ephone-dn 1 dual-line > number 3001 no-reg primary > label Br2 pHone 1 > name Br2 Phone 1 > call-forward busy 3600 > call-forward noan 3600 timeout 12 > ! > ! > > sip-ua > mwi-server ipv4:10.10.210.13 expires 3600 port 5060 transport udp > unsolicited > > ! > ! > ephone 1 > device-security-mode none > mac-address 001E.EC15.996D > type CIPC > button 1:1 > ! > > > > Thanks for the anticipated support > > >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com