Hi, I did a command "debug ephone moh"
When you see the below output you know that it's working: Mar 17 19:57:45.587: MoH route If Loopback0 46 10.10.110.2 via 10.10.110.2 Mar 17 19:57:45.587: MoH route If Vlan240 ETHERNET 10.10.201.1 via ARP Mar 17 19:57:47.983: ifs_read flash:music-on-hold.au end of file at 492841 read 3680 = 496521 Mar 17 19:57:47.987: moh tail fill from 24 at 0x4A725AF8 length 4320 Met vriendelijke groet, With kind regards, ing. Iwan Hoogendoorn, CCIE3 #13084 (R&S, Sec, SP) Homepage: http://www.i-1.nl Blog: http://blog.i-1.nl Twitter: http://www.twitter.com/iwan_ccie LinkedIn: http://www.linkedin.com/in/iwanhoogendoorn From: Roger Henderson [mailto:rhender...@gmail.com] Sent: zaterdag 27 maart 2010 16:20 To: Iwan Hoogendoorn Cc: Arun Kumar; ar...@ipexpert.com; ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] MOH Multicast from Router flash What did you do to prove that it is working? On Sun, Mar 28, 2010 at 2:19 AM, Iwan Hoogendoorn <i...@i-1.nl<mailto:i...@i-1.nl>> wrote: Roger, I don't understand your question .. For me it's working now ... Met vriendelijke groet, With kind regards, ing. Iwan Hoogendoorn, CCIE3 #13084 (R&S, Sec, SP) Homepage: http://www.i-1.nl Blog: http://blog.i-1.nl Twitter: http://www.twitter.com/iwan_ccie LinkedIn: http://www.linkedin.com/in/iwanhoogendoorn From: Roger Henderson [mailto:rhender...@gmail.com<mailto:rhender...@gmail.com>] Sent: zaterdag 27 maart 2010 16:18 To: Iwan Hoogendoorn Cc: Arun Kumar; ar...@ipexpert.com<mailto:ar...@ipexpert.com>; ccie_voice@onlinestudylist.com<mailto:ccie_voice@onlinestudylist.com> Subject: Re: [OSL | CCIE_Voice] MOH Multicast from Router flash Iwan, what did your testing entail? I spent 90 minutes on this tonight trying to prove my multicast MOH was working right. On Thu, Mar 18, 2010 at 6:03 PM, Iwan Hoogendoorn <i...@i-1.nl<mailto:i...@i-1.nl>> wrote: Thanks for the suggestions! Well after I did some intensive testing it is working as it should! Met vriendelijke groet, With kind regards, ing. Iwan Hoogendoorn, CCIE3 #13084 (R&S, Sec, SP) Homepage: http://www.i-1.nl Blog: http://blog.i-1.nl Twitter: http://www.twitter.com/iwan_ccie LinkedIn: http://www.linkedin.com/in/iwanhoogendoorn From: Arun Kumar [mailto:arunv...@gmail.com<mailto:arunv...@gmail.com>] Sent: donderdag 18 maart 2010 7:08 To: Iwan Hoogendoorn Cc: ccie_voice@onlinestudylist.com<mailto:ccie_voice@onlinestudylist.com> Subject: Re: [OSL | CCIE_Voice] MOH Multicast from Router flash show ccm-manager music-on-hold and you will see packet in/out value increasing. On Thu, Mar 18, 2010 at 1:35 AM, Iwan Hoogendoorn <i...@i-1.nl<mailto:i...@i-1.nl>> wrote: Hello, I am trying to multicast MOH from router flash and was wondering if there is any way to verify live MOH feed when a call is placed on hold on the Proctorlab Racks. According to Proctorlabs there is no way to hear MOH trough Multicast because of the the EzVPN (IPSec) connection... So this is what I am doing now: I have made a call from HQ to BR1 and at BR1 I have pressed Hold button. I can listen to the music but I am not sure if that is streaming from my router. I have also done "debug ephone moh" and "sh ip mroute". The outouts of both commands are as follows: ============================================================ Mar 17 19:57:45.587: MoH route If Loopback0 46 10.10.110.2 via 10.10.110.2 Mar 17 19:57:45.587: MoH route If Vlan240 ETHERNET 10.10.201.1 via ARP Mar 17 19:57:47.983: ifs_read flash:music-on-hold.au end of file at 492841 read 3680 = 496521 Mar 17 19:57:47.987: moh tail fill from 24 at 0x4A725AF8 length 4320 ============================================================ ============================================================ BR1-RTR-R#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group, V - RD & Vector, v - Vector Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.0.1.40), 00:43:45/00:02:21, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Loopback0, Forward/Sparse-Dense, 00:43:45/00:00:00 ============================================================ Now the result of these commands remain same whether I am in a live call or no call. Does this tell me that my MOH Multicasting from router flash is working fine? Any help would be appreciated. Met vriendelijke groet, With kind regards, ing. Iwan Hoogendoorn, CCIE3 #13084 (R&S, Sec, SP) Homepage: http://www.i-1.nl Blog: http://blog.i-1.nl Twitter: http://www.twitter.com/iwan_ccie LinkedIn: http://www.linkedin.com/in/iwanhoogendoorn _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com<http://www.ipexpert.com> _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com<http://www.ipexpert.com>
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com