Just make sure you understand the differences and can configure either method, 
regardless of the equipment setup.

Thanks,

Matthew Berry
Sr. Voice Engineer - CCIE 26721
Single Number Reach: +1.763.592.5987
[email protected]<mailto:[email protected]>

Check out my latest "Guru Guide" for QoS - http://ciscovoiceguru.com

From: [email protected] 
[mailto:[email protected]] On Behalf Of Rogers Ochieng
Sent: Wednesday, January 19, 2011 7:27 AM
To: Shrini
Cc: ccie_voice; Roger Källberg; bruno
Subject: Re: [OSL | CCIE_Voice] why trunk mode on ESW?

All recommendations i see prefers the new way, even though out of our scope 
it's more secure as compared to trunk mode.


On 19 January 2011 14:12, Shrini 
<[email protected]<mailto:[email protected]>> wrote:
Hi Roger,

I agree with "legacy" word, but I prefer trunk for our purpose, reason is below 
link.
access mode and trunk mode both explained well here.

http://www.cisco.com/en/US/docs/ios/lanswitch/configuration/guide/lsw_hwic_ethsw_ic_ps6441_TSD_Products_Configuration_Guide_Chapter.html#wp1049866

-S

________________________________
From: 
[email protected]<mailto:[email protected]>
 
[mailto:[email protected]<mailto:[email protected]>]
 On Behalf Of Roger Källberg
Sent: Wednesday, January 19, 2011 2:13 AM
To: bruno; ccie_voice
Subject: Re: [OSL | CCIE_Voice] why trunk mode on ESW?
Hi Bruno,
First of all I do not speak for IPX, but my understanding is that the reason 
for why the vol1 has the old way of configuring the ports on ESW module is 
because of at the time of when it was written this was the way these ports were 
configured.

I can from my own experience say that you definitely can configure these ports 
with the access port mode. This is what I did after I realized that this was 
now supported. But it might be good to practise on both methods, you never know 
if you will get that as a requirement in the lab.

Sincerely

Roger Källberg
CCIE #26199 (Voice)
Consultant
Cygate AB
Eric Perssons väg 21, SE-217 62 MALMÖ
________________________________
Från: bruno [[email protected]<mailto:[email protected]>]
Skickat: den 19 januari 2011 07:18
Till: ccie_voice
Ämne: [OSL | CCIE_Voice] why trunk mode on ESW?
Dear all
in vol1 network infrastrure,
why we need to configure trunk mode on esw,why not access mode .i have test the 
access mode is ok.
SITEB(config)#int range f0/1/0 -3
SITEB(config-if-range)# switchport trunk native vlan 602
SITEB(config-if-range)# switchport mode trunk
SITEB(config-if-range)# switchport voice vlan 502
SITEB(config-if-range)#description ***CONNECT TO IP PHONE***

SITEC#show interfaces f0/1/0 switchport
Name: Fa0/1/0
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 602 (DATA-VLAN)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1,502,602
Protected: false
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: 502
Appliance trust: none

Best Regards,
bruno



_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit 
www.ipexpert.com<http://www.ipexpert.com/>

_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit 
www.ipexpert.com

Reply via email to