Hi, for RDNIS you need "isdn outgoing ie redirect"
HTH kobel 2011/1/22 Michael Luo <hout...@gmail.com> > I have ""isdn outgoing display-ie" on the D channel. H323 gateway sent out > the caller ID. But it doesn't seem to send the "redirect party number". > Not sure why. > > 2011/1/22 Roger Källberg <roger.kallb...@cygate.se> > > Hi Michael, >> >> It most certainly also applies to H323 GW's, but you must also add "isdn >> outgoing display-ie" to the serial interface for the D channel. >> >> Sincerely >> >> *Roger Källberg* >> CCIE #26199 (Voice) >> Consultant >> Cygate AB >> Eric Perssons väg 21, SE-217 62 MALMÖ >> >> ------------------------------ >> *Från:* Michael Luo [hout...@gmail.com] >> *Skickat:* den 22 januari 2011 01:57 >> *Till:* ccie_voice@onlinestudylist.com >> *Ämne:* Re: [OSL | CCIE_Voice] AAR display >> >> Never mind. It's the "redirect IE" checkbox on outbound gateway. >> Interesting thing was, this only applies to MGCP but not H323 gateway. >> >> On Fri, Jan 21, 2011 at 5:56 PM, Michael Luo <hout...@gmail.com> wrote: >> >>> By the way, in CCM trace: >>> >>> 01/21/2011 16:48:03.289 CCM|StationD: (0000009) (2,100,9,20) CallInfo >>> callingPartyName='BR1 Phone1' callingParty=8631001 cgpnVoiceMailbox= >>> alternateCallingParty= calledPartyName='' >>> calledParty=12123945001 cdpnVoiceMailbox= >>> originalCalledPartyName='' originalCalledParty=5001 >>> originalCdpnVoiceMailbox= originalCdpnRedirectReason=1 >>> lastRedirectingPartyName='' >>> *lastRedirectingParty=5001*lastRedirectingVoiceMailbox= >>> *lastRedirectingReason=1* callType=2(OutBound) >>> lineInstance=1 callReference=48742317. version: >>> 85720011|<CLID::StandAloneCluster><NID::10.10.210.11><CT::2,100,39,1.3032><IP::10.10.201.254><DEV::SEP001F6C811391><LVL::State >>> Transition><MASK::0020> >>> >>> I think RedirectingReason=1 means "Call Forward Busy". But how? I tried >>> to call different phones in HQ site. They all display the same thing. >>> >>> >>> On Fri, Jan 21, 2011 at 5:54 PM, Michael Luo <hout...@gmail.com> wrote: >>> >>>> I was doing IPExpert volume 1 lab 6 task 6.1 - AAR (Automated Alternate >>>> Routing). >>>> >>>> Per the proctor guide, the configuration was pretty simple. I got it >>>> worked but observer strange behaviors. >>>> >>>> When HQ Phone1(5001) calls BR1 Phone1(1001) via AAR, the display on BR1 >>>> Phone1 was "From HQ Phone1", which was the expected behavior. >>>> >>>> But BR1 calls HQ, the display on HQ Phone1's screen was "Forward BR1 >>>> Phone1 For HQ Phone1". The call did go through. But I was curious why the >>>> display says "Forward". >>>> >>>> Any recommendation where I shall check? >>>> >>>> Thanks! >>>> Michael >>>> >>> >>> >> > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com