Also add isdn outgoing ie redirecting-number On 4 April 2011 08:35, Hannes Dippenaar <hanne...@hotmail.com> wrote:
> Hi, > > Please see below: > > interface Serial0/0/0:23 > description # To Hannes HQ Router ##### > no ip address > encapsulation hdlc > isdn switch-type primary-net5 > isdn protocol-emulate network > isdn incoming-voice voice > no cdp enable > end > > I have added "isdn outgoing display-ie" > > I will test and let you know. I did not know that "isdn outgoing > display-ie" affects the redirect number. > > thanks for the reply. > > > regards, > > Hannes > > ------------------------------ > From: gogli...@gmail.com > Date: Sun, 3 Apr 2011 14:59:10 -0700 > > Subject: Re: [OSL | CCIE_Voice] IPExpert Vol2 Lab 2 Q9.1 > To: hanne...@hotmail.com > CC: ccie_voice@onlinestudylist.com > > Hi, > > It must be PSTN Router configuration, looks like when the initial q931 > SETUP comes in, redirecting IE is there, but on the outgoing isdn q931 > message it's not there. > > can you post the "show run interface Se0/0/0:23" from PSTN router? > I'm sure it's missing "isnd outgoing display-ie" command. > > Regards, > > On Sun, Apr 3, 2011 at 11:20 AM, Hannes Dippenaar <hanne...@hotmail.com>wrote: > > Hi, Thank you for the reply, > > HQ = H323 > Br1 = MGCP > > I have enabled this on both HQ and BR1 GW's. > > No Luck. > > regards, > > Hannes > > ------------------------------ > From: gogli...@gmail.com > Date: Sun, 3 Apr 2011 06:59:20 -0700 > Subject: Re: [OSL | CCIE_Voice] IPExpert Vol2 Lab 2 Q9.1 > To: hanne...@hotmail.com > CC: ccie_voice@onlinestudylist.com > > > Hi Hannes, > > What is the HQ router MGCP gateway or h323? > If it's MGCP enable redirected number inbound on the MGCP GW configuration. > > On Sun, Apr 3, 2011 at 6:30 AM, Hannes Dippenaar <hanne...@hotmail.com>wrote: > > Good Day, > > I am busy with IPexpert Vol2 Lab2. > > I have configured the High Availability with aar and it works perfect > except for voicemail. > > If I dial from ext 5002 to ext 1002 and it transfers to voicemail. I can > see on my BR1 router that the redirecting number is included. > > It also get's to my PSTN router incoming POTS dialpeer. > > But when the PSTN router sends it off to HQ router POTS dialpeer the > redirecting number is no longer included. > > This means the Unity server do not recognise the phone I am trying to leave > a message for. > > How can I resolve this issue as I suspect it is caused by my PSTN router. > > I am including the debug from BR1,PSTN and HQ: > > BR1 > > *Apr 3 14:43:44.559: ISDN Se0/1/0:23 Q931: RX <- SETUP pd = 8 callref = > 0x00B0 > Bearer Capability i = 0x8090A2 > Standard = CCITT > Transfer Capability = Speech > Transfer Mode = Circuit > Transfer Rate = 64 kbit/s > Channel ID i = 0xA98381 > Exclusive, Channel 1 > Display i = 'HQph2' > Calling Party Number i = 0x2181, '2123945002' > Plan:ISDN, Type:National > Called Party Number i = 0x80, '16178631002' > Plan:Unknown, Type:Unknown > *Apr 3 14:43:44.767: ISDN Se0/1/0:23 Q931: TX -> CALL_PROC pd = 8 callref > = 0x80B0 > Channel ID i = 0xA98381 > Exclusive, Channel 1 > *Apr 3 14:43:44.771: ISDN Se0/1/0:23 Q931: TX -> ALERTING pd = 8 callref > = 0x80B0 > Progress Ind i = 0x8088 - In-band info or appropriate now available > > *Apr 3 14:43:56.751: ISDN Se0/1/0:23 Q931: TX -> SETUP pd = 8 callref = > 0x000D > Bearer Capability i = 0x8090A2 > Standard = CCITT > Transfer Capability = Speech > Transfer Mode = Circuit > Transfer Rate = 64 kbit/s > Channel ID i = 0xA98382 > Exclusive, Channel 2 > Display i = 'HQph2' > Calling Party Number i = 0x2183, '2123945002' > Plan:ISDN, Type:National > Called Party Number i = 0x80, '12123945600' > Plan:Unknown, Type:Unknown > Redirecting Number i = 0x000082, '1002' > Plan:Unknown, Type:Unknown > *Apr 3 14:43:56.775: ISDN Se0/1/0:23 Q931: RX <- CALL_PROC pd = 8 callref > = 0x800D > Channel ID i = 0xA98382 > Exclusive, Channel 2 > *Apr 3 14:43:59.827: ISDN Se0/1/0:23 Q931: RX <- ALERTING pd = 8 callref > = 0x800D > > > > > PSTN: > > Apr 3 13:08:39.735: ISDN Se0/3/0:23 Q931: RX <- SETUP pd = 8 callref = > 0x000D > Bearer Capability i = 0x8090A2 > Standard = CCITT > Transfer Capability = Speech > Transfer Mode = Circuit > Transfer Rate = 64 kbit/s > Channel ID i = 0xA98382 > Exclusive, Channel 2 > Display i = 'HQph2' > Calling Party Number i = 0x2183, '2123945002' > Plan:ISDN, Type:National > Called Party Number i = 0x80, '12123945600' > Plan:Unknown, Type:Unknown > Redirecting Number i = 0x000082, '1002' > Plan:Unknown, Type:Unknown > Apr 3 13:08:39.739: ISDN Se0/3/0:23 Q931: Received SETUP callref = 0x800D > callID = 0x00C9 switch = primary-ni interface = Network > Apr 3 13:08:39.739: ISDN Se0/3/0:23 Q931: extract_redirect_orig_called_ie: > IE type redirecting num 1002 reason 2 cnt -1 plan 0 type 0 pres 0 > Apr 3 13:08:39.743: ISDN Se0/0/0:23 Q931: Applying typeplan for sw-type > 0x12 is 0x2 0x1, Calling num 2123945002 > Apr 3 13:08:39.743: ISDN Se0/0/0:23 Q931: Sending SETUP callref = 0x00B1 > callID = 0x811E switch = primary-net5 interface = Network > Apr 3 13:08:39.747: ISDN Se0/3/0:23 Q931: TX -> CALL_PROC pd = 8 callref > = 0x800D > Channel ID i = 0xA98382 > Exclusive, Channel 2 > Apr 3 13:08:39.747: ISDN Se0/0/0:23 Q931: TX -> SETUP pd = 8 callref = > 0x00B1 > Bearer Capability i = 0x8090A2 > Standard = CCITT > Transfer Capability = Speech > Transfer Mode = Circuit > Transfer Rate = 64 kbit/s > Channel ID i = 0xA98381 > Exclusive, Channel 1 > Display i = 'HQph2' > Calling Party Number i = 0x2183, '2123945002' > Plan:ISDN, Type:National > Called Party Number i = 0x80, '2123945600' > Plan:Unknown, Type:Unknown > Apr 3 13:08:39.775: ISDN Se0/0/0:23 Q931: RX <- CALL_PROC pd = 8 callref > = 0x80B1 > Channel ID i = 0xA98381 > Exclusive, Channel 1 > > > HQ: > > Apr 3 13:08:39.755: ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8 callref = > 0x00B1 > Bearer Capability i = 0x8090A2 > Standard = CCITT > Transfer Capability = Speech > Transfer Mode = Circuit > Transfer Rate = 64 kbit/s > Channel ID i = 0xA98381 > Exclusive, Channel 1 > Display i = 'HQph2' > Calling Party Number i = 0x2183, '2123945002' > Plan:ISDN, Type:National > Called Party Number i = 0x80, '2123945600' > Plan:Unknown, Type:Unknown > Apr 3 13:08:39.759: ISDN Se0/0/0:23 Q931: Received SETUP callref = 0x80B1 > callID = 0x0010 switch = primary-net5 interface = User > Apr 3 13:08:39.775: ISDN Se0/0/0:23 Q931: TX -> CALL_PROC pd = 8 callref > = 0x80B1 > Channel ID i = 0xA98381 > Exclusive, Channel 1 > > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
