Hi Guys, Just to cut it short .. If you're on HQ-3750 then configure the phone ports as access ports and if you're configuring a switch module on a voice gateway then make it as trunk port. HQ-3750: ******** int f1/0/1 switchport access vlan 10 switchport mode access switchport voice vlan 20 spanning-tree portfast Switch Module: ************ int f1/1 switchport trunk native vlan 100 switchport mode trunk switchport voice vlan 200 BRgds, Ramy
Date: Tue, 24 Apr 2012 05:49:41 +0100 From: ke...@kevinspicer.co.uk To: devsin2...@gmail.com CC: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] Router Switch port configurations Actually Chris Bill's post has me worried. How many other people have seen this behavior? There's not a lot to choose between the 2, and if one is more stable... On 24 Apr 2012 04:22, "Chris" <devsin2...@gmail.com> wrote: Thanks Juan. Hi ST, What you are saying is not quiet correct. Option 2 will normally be okay. However, if we want to be sure, we could include "allowed vlan" keyword. This option must always work at least when you have "allowed VLAN" configured, and vlan pruning is disabled. The "switchport voice vlan" is Cisco's special for Cisco phone. But some other vendors have also taken up this approach. I my opinion if we can use it option 1 we should use it. From responses from Kevin and Juan, it seems like it works fine. I think we can challenge if this doesn't work in lab. I was originally unsure of if this command would be available on piddly little four port switch module. Chris. On Mon, Apr 23, 2012 at 11:45 PM, Seifeddine Tlili <seifeddine.tl...@lvs1.com> wrote: But in option 2 you still missing the switchport voice vlan 11 ortherwise you have to specify it manually on each phone, for third party SIP Phone it`s has to be that way Thanks ST From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Juan Lopez Sent: Monday, April 23, 2012 6:33 AM To: Chris Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] Router Switch port configurations I always use the second option, never had any issue with it... cheers Juan Op 22 april 2012 15:56 schreef Chris <devsin2...@gmail.com> het volgende: Hi All , I don't have a 4-port or 9-port POE switch module to try it on. Therefore I would like for some one to confirm if both or one of following port configuration will work on these cards. I do understand the concept, but don't want to find the actual syntax on lab day :). Thanks in advance. Vlan 10 is DATA Vlan 11 is VOICE Preference 1- interface FastEthernet0/1/0 switchport access vlan 10 switchport voice vlan 11 spanning-tree portfast Preference 2- interface FastEthernet0/1/0 switchport trunk native vlan 10 switchport mode trunk Best Regards Chris _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com