I reloaded the router and reapplied the QoS configuration. No dice. Still not matching in the nested policy. Very weird that it is working like a champ in the SB router. I've done this a couple times in the past and never run into this issue. I'm going to play with it a little longer, but may have to come back to it in the morning with a fresh set of coffee fueled eyes...
On Sun, Mar 3, 2013 at 10:07 PM, Bill <whl...@gmail.com> wrote: > Well it looks like it is picking up the RTP header compression, shaping > and even the service policy but not doing it. > > Have you tried rebooting the router or copy, delete then reapply ? > > > Sent from my iPad > > On Mar 3, 2013, at 8:43 PM, Jason Lee <jas7...@gmail.com> wrote: > > All, > > Was wondering if I could get a second set of eyes on my Class Based > Shaping configuration. I just implemented between SA and SB. The same > configuration is used on both. On SB I see the packets being captured in > both policy maps. On SA I don't see traffic being captured in the nested > policy-map containing voice and signaling configuration. Heres the > output... > > > r3800-2j-a(config)#do sh policy-map inter s0/2/0.1 > Serial0/2/0.1: DLCI 201 - > > Service-policy output: shape-policy-map > > Class-map: class-default (match-any) > 3234 packets, 563006 bytes > 5 minute offered rate 0 bps, drop rate 0 bps > Match: any > Queueing > queue limit 64 packets > (queue depth/total drops/no-buffer drops) 0/0/0 > (pkts output/bytes output) 3234/545846 > shape (average) cir 384000, bc 3840, be 0 > target shape rate 384000 > lower bound cir 0, adapt to fecn 0 > compress: > header ip rtp > UDP/RTP (compression on, Cisco, RTP) > Sent: 455 total, 452 compressed, > 17160 bytes saved, 10140 bytes sent > 2.69 efficiency improvement factor > 99% hit ratio, five minute miss rate 0 misses/sec, 0 > max > rate 0 bps > > > Service-policy : llq > > queue stats for all priority classes: > > queue limit 64 packets > (queue depth/total drops/no-buffer drops) 0/0/0 > (pkts output/bytes output) 0/0 > > r3800-2j-a(config)#do sh policy-map inter s0/2/0.1 > Serial0/2/0.1: DLCI 201 - > > Service-policy output: shape-policy-map > > Class-map: class-default (match-any) > 3234 packets, 563006 bytes > 5 minute offered rate 0 bps, drop rate 0 bps > Match: any > Queueing > queue limit 64 packets > (queue depth/total drops/no-buffer drops) 0/0/0 > (pkts output/bytes output) 3234/545846 > shape (average) cir 384000, bc 3840, be 0 > target shape rate 384000 > lower bound cir 0, adapt to fecn 0 > compress: > header ip rtp > UDP/RTP (compression on, Cisco, RTP) > Sent: 455 total, 452 compressed, > 17160 bytes saved, 10140 bytes sent > 2.69 efficiency improvement factor > 99% hit ratio, five minute miss rate 0 misses/sec, 0 > max > rate 0 bps > > > Service-policy : llq > > queue stats for all priority classes: > > queue limit 64 packets > (queue depth/total drops/no-buffer drops) 0/0/0 > (pkts output/bytes output) 0/0 > > Class-map: voice (match-all) > 0 packets, 0 bytes > 5 minute offered rate 0 bps, drop rate 0 bps > Match: ip dscp ef (46) > Match: protocol rtp > Match: protocol rtcp > Priority: 24 kbps, burst bytes 1500, b/w exceed drops: 0 > > > Class-map: signal (match-all) > 0 packets, 0 bytes > 5 minute offered rate 0 bps, drop rate 0 bps > Match: ip dscp cs3 (24) > Match: protocol sip > Match: protocol h323 > Match: protocol mgcp > Match: protocol skinny > Queueing > queue limit 64 packets > (queue depth/total drops/no-buffer drops) 0/0/0 > (pkts output/bytes output) 0/0 > bandwidth 18 kbps > > Class-map: class-default (match-any) > 3234 packets, 563006 bytes > 5 minute offered rate 0 bps, drop rate 0 bps > Match: any > > queue limit 64 packets > (queue depth/total drops/no-buffer drops) 0/0/0 > (pkts output/bytes output) 3234/545846 > r3800-2j-a(config)# > 5 minute offered rate 0 bps, drop rate 0 bps > Match: ip dscp ef (46) > Match: protocol rtp > Match: protocol rtcp > Priority: 24 kbps, burst bytes 1500, b/w exceed drops: 0 > > > * Class-map: signal (match-all)* > * 0 packets, 0 bytes* > 5 minute offered rate 0 bps, drop rate 0 bps > Match: ip dscp cs3 (24) > Match: protocol sip > Match: protocol h323 > Match: protocol mgcp > Match: protocol skinny > Queueing > queue limit 64 packets > (queue depth/total drops/no-buffer drops) 0/0/0 > (pkts output/bytes output) 0/0 > bandwidth 18 kbps > > Class-map: class-default (match-any) > 3234 packets, 563006 bytes > 5 minute offered rate 0 bps, drop rate 0 bps > Match: any > > queue limit 64 packets > (queue depth/total drops/no-buffer drops) 0/0/0 > (pkts output/bytes output) 3234/545846 > r3800-2j-a(config)# > > > > > Here's my config: > > > r3800-2j-a#sh run > Building configuration... > > > Current configuration : 6530 bytes > ! > ! Last configuration change at 18:42:14 PST Sun Mar 3 2013 > ! NVRAM config last updated at 15:00:54 PST Fri Mar 1 2013 > ! > version 12.4 > service timestamps debug datetime msec > service timestamps log datetime msec > no service password-encryption > ! > hostname r3800-2j-a > ! > boot-start-marker > boot system flash c3825-adventerprisek9_ivs_li-mz.124-24.T4.bin > boot-end-marker > ! > card type t1 0 0 > logging message-counter syslog > no logging buffered > no logging console > enable password cisco > ! > no aaa new-model > clock timezone PST -8 > network-clock-participate wic 0 > network-clock-select 1 T1 0/0/0 > ! > dot11 syslog > ip source-route > ip cef > ! > ! > ip dhcp excluded-address 192.168.102.0 192.168.102.49 > ip dhcp excluded-address 192.168.102.60 192.168.102.255 > ip dhcp excluded-address 192.168.104.0 192.168.104.49 > ip dhcp excluded-address 192.168.104.60 192.168.104.255 > ip dhcp excluded-address 192.168.106.0 192.168.106.49 > ip dhcp excluded-address 192.168.106.60 192.168.106.255 > ! > ip dhcp pool sa > network 192.168.102.0 255.255.255.0 > default-router 192.168.102.1 > option 150 ip 192.168.100.101 192.168.100.100 > ! > ip dhcp pool sb > network 192.168.104.0 255.255.255.0 > default-router 192.168.104.1 > option 150 ip 192.168.100.101 192.168.100.100 > ! > ip dhcp pool sc > network 192.168.106.0 255.255.255.0 > default-router 192.168.106.1 > option 150 ip 192.168.100.101 192.168.100.100 > ! > ! > no ip domain lookup > ip domain name cisco.com > no ipv6 cef > ! > multilink bundle-name authenticated > ! > ! > ! > ! > isdn switch-type primary-ni > ! > voice-card 0 > dsp services dspfarm > ! > ! > ! > voice service voip > allow-connections h323 to h323 > allow-connections h323 to sip > allow-connections sip to h323 > allow-connections sip to sip > fax protocol cisco > ! > ! > ! > voice class codec 1 > codec preference 1 g711ulaw > codec preference 2 g729r8 > ! > ! > ! > ! > voice class h323 1 > h225 timeout tcp establish 3 > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > archive > log config > hidekeys > ! > ! > ! > ! > ! > controller T1 0/0/0 > cablelength long 0db > pri-group timeslots 1-3,24 service mgcp > ! > controller T1 0/0/1 > cablelength long 0db > ! > ! > class-map match-all signal > match ip dscp cs3 > match protocol sip > match protocol h323 > match protocol mgcp > match protocol skinny > class-map match-all voice > match ip dscp ef > match protocol rtp > match protocol rtcp > ! > ! > policy-map llq > class voice > priority 24 > class signal > bandwidth 18 > policy-map shape-policy-map > class class-default > shape average 384000 3840 0 > compress header ip rtp > service-policy llq > ! > ! > ! > ! > ! > interface Loopback0 > ip address 192.168.96.10 255.255.255.255 > h323-gateway voip interface > h323-gateway voip id VIA ipaddr 192.168.96.10 1719 > h323-gateway voip h323-id CUBE > h323-gateway voip bind srcaddr 192.168.96.10 > ! > interface GigabitEthernet0/0 > no ip address > duplex full > speed 100 > media-type rj45 > ! > interface GigabitEthernet0/0.100 > encapsulation dot1Q 100 native > ip address 192.168.100.1 255.255.255.0 > ! > interface GigabitEthernet0/0.101 > encapsulation dot1Q 101 > ip address 192.168.101.1 255.255.255.0 > ! > interface GigabitEthernet0/0.102 > encapsulation dot1Q 102 > ip address 192.168.102.1 255.255.255.0 > ! > interface GigabitEthernet0/1 > description Lab_GW_DO_NOT_DISABLE > ip address 172.16.1.251 255.255.0.0 > load-interval 30 > duplex auto > speed auto > media-type rj45 > ! > interface FastEthernet0/3/0 > ! > interface FastEthernet0/3/1 > ! > interface FastEthernet0/3/2 > ! > interface FastEthernet0/3/3 > ! > interface Serial0/0/0:23 > no ip address > encapsulation hdlc > isdn switch-type primary-ni > isdn incoming-voice voice > isdn bind-l3 ccm-manager > isdn outgoing display-ie > no cdp enable > ! > interface Serial0/2/0 > no ip address > encapsulation frame-relay > frame-relay lmi-type ansi > ! > interface Serial0/2/0.1 point-to-point > description FR-WAN TO r2800-2j-a - DLCI 201 > ip address 192.168.111.5 255.255.255.252 > ip ospf mtu-ignore > frame-relay interface-dlci 201 > class shape-map-class > ! > interface Serial0/2/0.2 point-to-point > description FR-WAN TO r2800-2j-b - DLCI 202 > ip address 192.168.111.9 255.255.255.252 > ip ospf mtu-ignore > frame-relay interface-dlci 202 > ! > interface Serial0/2/1 > no ip address > encapsulation ppp > shutdown > clock rate 2000000 > ! > interface Vlan1 > no ip address > ! > router ospf 1 > log-adjacency-changes > network 192.168.0.0 0.0.255.255 area 0 > ! > ip forward-protocol nd > ip route 0.0.0.0 0.0.0.0 172.16.1.1 name LAB_GW_DO_NOT_REMOVE > ip route 192.168.110.0 255.255.255.0 192.168.101.2 name PSTN_LAN > no ip http server > no ip http secure-server > ! > ! > ! > ! > map-class frame-relay shape-map-class > frame-relay fragment 480 > frame-relay fair-queue > service-policy output shape-policy-map > ! > ! > ! > ! > ! > ! > control-plane > ! > ! > ! > voice-port 0/0/0:23 > ! > voice-port 0/1/0 > ! > voice-port 0/1/1 > ! > ccm-manager redundant-host 192.168.100.100 > ccm-manager mgcp > no ccm-manager fax protocol cisco > ccm-manager music-on-hold > ccm-manager config server 192.168.100.100 > ! > mgcp > mgcp call-agent 192.168.100.101 2427 service-type mgcp version 0.1 > mgcp dtmf-relay voip codec all mode out-of-band > mgcp modem passthrough voip mode nse > mgcp package-capability rtp-package > mgcp package-capability sst-package > mgcp package-capability pre-package > mgcp default-package mt-package > no mgcp timer receive-rtcp > mgcp sdp simple > mgcp fax t38 ecm > mgcp fax t38 inhibit > mgcp bind control source-interface Loopback0 > mgcp bind media source-interface Loopback0 > ! > mgcp profile default > ! > sccp local Loopback0 > sccp ccm 192.168.100.101 identifier 1 version 7.0 > sccp ccm 192.168.100.100 identifier 2 version 7.0 > sccp > ! > sccp ccm group 1 > associate ccm 1 priority 1 > associate ccm 2 priority 2 > associate profile 1 register sa-xcode > associate profile 2 register sa-conf > ! > dspfarm profile 1 transcode > codec g711ulaw > codec g711alaw > codec g729ar8 > codec g729abr8 > codec g729r8 > maximum sessions 4 > associate application SCCP > ! > dspfarm profile 2 conference > codec g711ulaw > codec g711alaw > codec g729ar8 > codec g729abr8 > codec g729r8 > codec g729br8 > maximum sessions 2 > associate application SCCP > ! > ! > dial-peer voice 9167 voip > voice-class h323 1 > incoming called-number 9167 > dtmf-relay h245-alphanumeric > no vad > ! > dial-peer voice 91671 voip > destination-pattern 9167 > session target ras > dtmf-relay h245-alphanumeric > no vad > ! > ! > gateway > timer receive-rtp 1200 > ! > ! > ! > gatekeeper > zone local USUK ipexpert.com 192.168.96.10 > zone local VIA ipexpert.com > zone remote INDIA ipexpert.com 192.168.101.2 1719 outvia VIA > zone prefix INDIA 9167* > no shutdown > ! > ! > line con 0 > line aux 0 > line vty 0 4 > password cisco > login > ! > scheduler allocate 20000 1000 > ntp server 172.16.1.1 > end > > r3800-2j-a# > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com > >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
