application service cmm http://10.10.210.10:8080/ccmivr/pages/IVRMainpage.vxml dial-peer voice 2 pots service ccm ccm ---> cmm ? Date: Wed, 15 May 2013 23:48:40 -0400 From: josh.pe...@gmail.com To: ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] MVA Fast Busy
Hi All, I'm on Volume 1 section 5C which is asking for Mobile Vocie Access configuration. What I'm getting when I dial from the PSTN to the HQ Phone 2 is a fast busy after a few seconds of silence. I know this has been talked about in the past on this forum, but for the life of me I can't find it. I've followed what was in the workbook exactly and I'm not getting anywhere. Now, I'm doing this on my home lab with IOS 12.4.22T5 and nothing else in the flash directory. Is there something that needs to be 'installed' on the router to allow it to see the vxml code on the CUCM? I've never been asked to do Mobile Voice Access before, so this is a first. The CUCM is configured with the Mobile Voice Access number of 5999 and the gateway is configured for 4 digits inbound (plus I tested other inbound calls and they still work fine). The Services parameters are correct and MVA is enabled. The voice-class codec has G711u and G729r8 and that's it. I'm thinking codec, but I'm not sure why. I can't figure out what I missed. Many thanks!Josh The config and debug isdn q931 output is below if it helps. I didn't get the chance to get the voip ccapi debugs, so please let me know if you need them and I'll grab them tomorrow. !application service cmm http://10.10.210.10:8080/ccmivr/pages/IVRMainpage.vxml !! dial-peer voice 5010 voip description MVA DID destination-pattern 5999 voice-class codec 1 session target ipv4:10.10.210.10 incoming called-number . dtmf-relay h245-alphanumeric no vad!dial-peer voice 2 pots service ccm incoming called-number 2123945999 no digit-strip!!!!! !HQ-RTR(config-dial-peer)#May 16 03:12:37.874: ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8 callref = 0x00A1 Bearer Capability i = 0x8090A2 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98381 Exclusive, Channel 1 Progress Ind i = 0x8583 - Origination address is non-ISDN Calling Party Number i = 0x4180, '2123942123' Plan:ISDN, Type:Subscriber(local) Called Party Number i = 0xA1, '2123945999' Plan:ISDN, Type:NationalMay 16 03:12:37.874: ISDN Se0/0/0:23 Q931: Received SETUP callref = 0x80A1 callID = 0x0020 switch = primary-ni interface = User May 16 03:12:37.882: %CALL_CONTROL-6-APP_NOT_FOUND: Application ccm in dial-peer 2 not found. Handing callid 187 to the alternate app . HQ-RTR(config-dial-peer)#May 16 03:12:37.890: ISDN Se0/0/0:23 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x80A1 Cause i = 0x80BF - Service/option not available, unspecified HQ-RTR(config-dial-peer)# _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
