On 2017-Mar-30, at 1:13 PM, Noel Chiappa via cctalk wrote:
>> From: Allison
>
>> FYI this is the same problem designers hit with DRAMS back 40 years ago.
>
> This didn't ring (pun not intended) a bell for me; can you say a bit more?
>
>> From: Chuck Guzis
>
>> I'll offer a suggestion that if your SD card *must* be a significant
>> distance from its host
>
> Like I said, this is a pre-prototype; on the production units, there will be
> _no_ cable. The SD socket will be about 1-2" from the FPGA.
>
>> From: Dwight Kelvey
>
>> this behavior on my PDP-8/e where a 7474 flip flop chip was bad. The
>> input looked great and the output was "half baked"
>
> There's no chip at all on the driving end of the line (just that 470K
> resistor); we see this with the SD card _unplugged_. And we see the exact
> same thing on several lines.
>
>
> I'm still not clear, from the discussion, how exactly that nice 'square-wave'
> interference is happening - could it be capacitative crosstalk? (I'd have
> thought capacitative cross-talk would be inverted - driving a positive voltage
> on one 'side' of the 'capacitor' would, I would think, induce an oppposing
> voltage on the other. But I'm clearly no EE! :-)
I don't have a full enough picture of the circuit and circumstances to provide
a definitive suggestion but, some principles:
Yes, you can 'pass' a square wave through a capacitor - if you couldn't then
all the theory behind capacitor-coupled audio amplifiers would be shot.
The condition required to do so is a long resistor - capacitor time constant
relative to the period of the (square) wave:
RC time constant: t(seconds) = R (ohms) * C (farads)
With a high load R, and large enough C, the current in an R-C series circuit is
limited to a tiny level, so it takes a long time for the cap to fully charge.
For as long as the cap is charging there is current flowing through the R and
so you see a voltage drop across the R.
If you reduce the R value or the C value, at some point you would see the
square wave start to distort (the flat top would start to slope down to the
right / later in time),
as the capacitor would start to reach full charge within the period of the
square wave and the voltage would start to divide between the C and R.
No, you won't see the inverse polarity, if you drive a + voltage to one side of
the cap it sucks the electrons out of the plate on that side, that attracts
electrons into the other 'load-side' plate. Those electrons are coming from
(being drawn away from) the rest of the load side circuit, here through the R,
so you see a + voltage across the R (current is flowing from GND through R into
the C, so the RC-junction side of R is more + than the GND side of the R).
Your circuit:
It's not clear C-coupling is what's going on here (the wave shape looks pretty
sharp for what I understand of the circuit/layout).
Notably though, C-coupling would remove any DC bias, but David's screen shot
indicates a DC bias on the line.
Is this line currently connected to the FPGA, or is it just the wire and R?
Perhaps the bias is coming from the FPGA, with C-coupling of the wave via the
wire.
Or perhaps it's all crosstalk from within the FPGA, 'visible' because of the
high load R.
If the wire and FPGA pin are connected, separate them (reduce the wire circuit
to just the wire and R to GND): see whether the DC bias and/or the square wave
disappear.
You could play with reducing the load R value to see what happens to the sig
level and wave shape.
(You've mentioned both 470K and 270K for the R, could make a difference to the
analysis).
