On Tue, Apr 20, 2004 at 05:58:51PM +0200, Joerg Schilling wrote: > >From: Gregoire Favre <[EMAIL PROTECTED]> > > >Normally, I use this script to write my DVD (video): > > >#!/bin/tcsh > > >setenv SIZE `mkisofs -dvd-video -f -q -print-size -V $1 $2` > >setenv CDR_SECURITY "8:d ... " > >mkisofs -dvd-video -f -V $1 $2 | cdrecord-prodvd -v dev=ATAPI:0,0,0 fs=64m speed=1 > >-eject -dao tsize={$SIZE}s - > > >(I am running kernel 2.6.5-mm6) > > >What should I do to use the DVD+R and become a maximum DVD video > >compatibility? > > The same command as above
Well, not a success: mkisofs: Warning: -follow-links does not always work correctly; be careful. mkisofs: Warning: -follow-links does not always work correctly; be careful. Cdrecord-ProDVD-Clone 2.01a20 (i686-pc-linux-gnu) Copyright (C) 1995-2003 Jörg Schilling Unlocked features: ProDVD Clone Limited features: This copy of cdrecord is licensed for: private/research/educational_non-commercial_use TOC Type: 1 = CD-ROM scsidev: 'ATAPI:0,0,0' devname: 'ATAPI' scsibus: 0 target: 0 lun: 0 Warning: Using ATA Packet interface. Warning: The related libscg interface code is in pre alpha. Warning: There may be fatal problems. Using libscg version 'schily-0.7'. SCSI buffer size: 64512 atapi: 1 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : 'SONY ' Identifikation : 'DVD RW DRU-500A ' Revision : '2.0h' Device seems to be: Generic mmc2 DVD-R/DVD-RW. Current: DVD+R Profile: DVD+R (current) Profile: DVD+RW Profile: DVD-RW sequential overwrite Profile: DVD-RW restricted overwrite Profile: DVD-R sequential recording Profile: DVD-ROM Profile: CD-RW Profile: CD-R Profile: CD-ROM Using generic SCSI-3/mmc-3 DVD+R driver (mmc_dvdplusr). Driver flags : DVD MMC-3 SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R Drive buf size : 4718592 = 4608 KB FIFO size : 67108864 = 65536 KB Track 01: data 3573 MB Total size: 3573 MB = 1829399 sectors Current Secsize: 2048 Blocks total: 2295104 Blocks current: 2295104 Blocks remaining: 465705 Starting to write CD/DVD at speed 4 in real SAO mode for single session. Last chance to quit, starting real write in 9 seconds. 0.27% done, estimate finish Wed Apr 21 22:52:22 2004 0.55% done, estimate finish Wed Apr 21 22:52:22 2004 0.82% done, estimate finish Wed Apr 21 22:52:22 2004 1.09% done, estimate finish Wed Apr 21 22:52:22 2004 1.37% done, estimate finish Wed Apr 21 22:53:35 2004 8 seconds. 1.64% done, estimate finish Wed Apr 21 22:53:22 2004 0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. Starting new track at sector: 0 Track 01: 4 of 3573 MB written (fifo 99%) [buf 92%] 11.6x.cdrecord-prodvd: Input/output error. write_g1: scsi sendcmd: no error CDB: 2A 00 00 00 08 B8 00 00 1F 00 status: 0x2 (CHECK CONDITION) Sense Bytes: F1 00 03 FF FD 00 00 12 00 00 00 00 73 03 00 00 00 00 00 00 00 00 00 00 00 00 Sense Key: 0x3 Medium Error, deferred error, Segment 0 Sense Code: 0x73 Qual 0x03 (power calibration area error) Fru 0x0 Sense flags: Blk -196608 (valid) cmd finished after 63.710s timeout 100s write track data: error after 4571136 bytes cdrecord-prodvd: A write error occured. cdrecord-prodvd: Please properly read the error message above. Writing time: 69.045s Average write speed 39.2x. Fixating... Fixating time: 0.002s cdrecord-prodvd: fifo had 1095 puts and 73 gets. cdrecord-prodvd: fifo was 0 times empty and 8 times full, min fill was 99%. > Note that with dev=ATAPI: you will never get DMA and writing is soooo slow. Also for that point, I have read the doc, but didn't find any info on what I should put instaed, anyone could give me the answer? Thank you very much, Grégoire __________________________________________________________________________ http://algebra.epfl.ch/greg ICQ:16624071 mailto:[EMAIL PROTECTED]