Hello, I just tried to burn a DVD under OSX:
Cdrecord-ProDVD-Clone 2.01a11 (powerpc-apple-macosx1.4) Copyright (C) 1995-2003 Jörg Schilling Unlocked features: ProDVD Clone Limited features: This copy of cdrecord is licensed for: private/research/educational_non-commercial_use TOC Type: 1 = CD-ROM scsidev: 'IODVDServices' devname: 'IODVDServices' scsibus: -2 target: -2 lun: -2 Using libscg version 'schily-0.7' cdrecord-prodvd: Warning: using inofficial libscg transport code version (csapuntz-scsi-mac-iokit.c-1.4 '@(#)scsi-mac-iokit.c 1.4 02/10/19 Copyright 1997,2001 J. Schilling'). atapi: 0 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : 'MATSHITA' Identifikation : 'DVD-R UJ-816 ' Revision : 'DXJ3' Device seems to be: Generic mmc2 DVD-R/DVD-RW. Profile: DVD-RW restricted overwrite Profile: DVD-RW sequential overwrite Profile: DVD-R sequential recording (current) Profile: DVD-ROM Profile: CD-RW Profile: CD-R Profile: CD-ROM Profile: Removable Disk Using generic SCSI-3/mmc-2 DVD-R/DVD-RW driver (mmc_dvd). Driver flags : DVD MMC-3 SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO Drive buf size : 1671168 = 1632 KB FIFO size : 67108864 = 65536 KB Track 01: data 4472 MB Total size: 4472 MB = 2290112 sectors Current Secsize: 2048 WARNING: Phys disk size 1 differs from rzone size 2298496! Prerecorded disk? WARNING: Phys start: 196608 Phys end 196608 Blocks total: 2298496 Blocks current: 2298496 Blocks remaining: 8384 Starting to write CD/DVD at speed 2 in real SAO mode for single session. Last chance to quit, starting real write 8 seconds. 0.22% done, estimate finish Wed Dec 17 21:54:04 2003 7 seconds. 0.44% done, estimate finish Wed Dec 17 21:50:15 2003 0.66% done, estimate finish Wed Dec 17 21:46:26 2003 6 seconds. 0.87% done, estimate finish Wed Dec 17 21:46:26 2003 5 seconds. 1.09% done, estimate finish Wed Dec 17 21:46:27 2003 4 seconds. 1.31% done, estimate finish Wed Dec 17 21:46:26 2003 0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. BURN-Free is ON. Turning BURN-Free off Starting new track at sector: 0 Track 01: 4 of 4472 MB written (fifo 100%) [buf 100%] 1.0x. 1.53% done, estimate finish Wed Dec 17 22:13:42 2003 Track 01: 14 of 4472 MB written (fifo 100%) [buf 100%] 1.0x. 1.75% done, estimate finish Wed Dec 17 22:16:58 2003 Track 01: 23 of 4472 MB written (fifo 100%) [buf 100%] 1.0x. 1.97% done, estimate finish Wed Dec 17 22:18:40 2003 ... Track 01: 4408 of 4472 MB written (fifo 100%) [buf 100%] 1.0x.100.00% done, estimate finish Wed Dec 17 22:34:50 2003 Track 01: 4409 of 4472 MB written (fifo 99%) [buf 96%] 0.9x.Total translation table size: 0 Total rockridge attributes bytes: 0 Total directory bytes: 4096 Path table size(bytes): 42 Max brk space used 0 2290112 extents written (4472 Mb) Track 01: 4429 of 4472 MB written (fifo 100%) [buf 100%] 1.0x.cdrecord-prodvd: Error 0. write_g1: scsi sendcmd: no error CDB: 2A 00 00 22 9B E0 00 00 10 00 status: 0x2 (CHECK CONDITION) Sense Bytes: F1 00 04 00 22 98 B0 0A 00 2A 00 00 03 00 00 00 00 00 Sense Key: 0x4 Hardware Error, deferred error, Segment 0 Sense Code: 0x03 Qual 0x00 (peripheral device write fault) Fru 0x0 Sense flags: Blk 2267312 (valid) resid: 32768 cmd finished after 1.574s timeout 100s write track data: error after 4645126144 bytes cdrecord-prodvd: A write error occured. cdrecord-prodvd: Please properly read the error message above. Writing time: 3372.130s Average write speed 1.0x. Min drive buffer fill was 70% Fixating... Fixating time: 0.000s cdrecord-prodvd: fifo had 143132 puts and 141759 gets. cdrecord-prodvd: fifo was 0 times empty and 90979 times full, min fill was 95%. And I don't understand the error??? Bad media? And why is the burn only at speed 1? Thank you very much, Grégoire ________________________________________________________________________ http://magma.epfl.ch/greg ICQ:16624071 mailto:[EMAIL PROTECTED]