On Wed, 26 Dec 2007, Robert Moskowitz wrote:
Scott Ehrlich wrote:
On Tue, 25 Dec 2007, Robert Moskowitz wrote:
Scott Ehrlich wrote:
On Tue, 25 Dec 2007, Robert Moskowitz wrote:
Scott Ehrlich wrote:
On Tue, 25 Dec 2007, Robert Moskowitz wrote:
Frank Cox wrote:
On Tue, 25 Dec 2007 17:37:32 -0500
Robert Moskowitz <[EMAIL PROTECTED]> wrote:
Sense Key: 0x2 Not Ready, Segment 0
Get some canned air and blow the dirt off of the sensor in the drive.
No change.
The drive is the coffee mug tray style. so even opening the plastic
housing for the drive does not let me 'see' the sensor, but I used a
lot of canned air and no change in behaviour....
Perhaps I have to go out to the drug store and buy one of those drive
lens cleaner disks?
Have you tried removing/reseating the data cable on both ends?
USB. I thought I mentioned that....
I've seen this work a handful of times. Also, SCSI or other? If SCSI,
is it properly terminated, and with the correct ID? I once replaced a
SCSI hard drive, and due to some technical change that completely
baffled me, using the same cable, and ensuring IDs were all correct
(unchanged), could not get the system to properly boot? In the end, a
colleague with similar knowledge ended up relocating the SCSI
terminator on the cable itself. No reason why it needed to be
relocated, but that solved the problem.
Yeah if those SCSI terminators get a little dirty ;)
Try cabling and see what happens...
Using 2.0 cables. Of course the server is an old Compaq SFF that only
supports USB 1.1
What do the logs say about any possible USB errors? How about tail -f
path_to_log_file and unplugged/replugging to see what the active messages
are?
Dec 25 20:46:02 onlo kernel: usb 1-2: reset full speed USB device using
uhci_hcd and address 2
Dec 25 20:46:02 onlo kernel: usb 1-2: reset full speed USB device using
uhci_hcd and address 2
Dec 25 20:46:03 onlo kernel: sr 0:0:0:0: scsi: Device offlined - not ready
after error recovery
Dec 25 20:46:03 onlo kernel: sr 0:0:0:0: rejecting I/O to offline device
Dec 25 21:53:01 onlo kernel: sr 0:0:0:0: rejecting I/O to offline device
I terminated k3b at this point and unplugged and plugged in the usb cable
to the drive:
Dec 25 21:54:07 onlo kernel: usb 1-2: USB disconnect, address 2
Dec 25 21:54:28 onlo kernel: usb 1-2: new full speed USB device using
uhci_hcd and address 3
Dec 25 21:54:28 onlo kernel: usb 1-2: configuration #1 chosen from 1
choice
Dec 25 21:54:32 onlo kernel: scsi1 : SCSI emulation for USB Mass Storage
devices
Dec 25 21:54:37 onlo kernel: Vendor: HP Model: CD-Writer+ 8200f Rev: 1.0A
Dec 25 21:54:37 onlo kernel: Type: CD-ROM ANSI SCSI revision: 00
Dec 25 21:54:37 onlo kernel: sr0: scsi3-mmc drive: 32x/32x writer cd/rw
xa/form2 cdda tray
Dec 25 21:54:37 onlo kernel: sr 1:0:0:0: Attached scsi generic sg0 type 5
k3b uses cdrecord among other utilities - it is simply a graphical
front-end.
Have you tried the command-line tools instead?
I have a simple script that collects files, creates an ISO, then burns the
ISO to disk. No GUI (k3b) involved.
mkisofs -o /home/scott/files.iso -R -J -T files/
cdrecord -v dev=/dev/cdrom -multi /home/scott/files.iso
eject
Why the -multi option?
To permit multisession and not close the disc. If you want to close it
(write once, that's it), then remove the -multi.
Scott
_______________________________________________
CentOS mailing list
CentOS@centos.org
http://lists.centos.org/mailman/listinfo/centos
_______________________________________________
CentOS mailing list
CentOS@centos.org
http://lists.centos.org/mailman/listinfo/centos