----- Original Message ----- | On Fri, Aug 19, 2016 at 4:59 PM, James A. Peltier <jpelt...@sfu.ca> wrote: | > | > | > ----- Original Message ----- | > | On Thu, Aug 18, 2016 at 11:57 AM, James A. Peltier <jpelt...@sfu.ca> | > | wrote: | > | > Hi All, | > | > | > | > I have a Dell R710 that has 6x1TB in a RAID-5 configuration. | > | | > | | > | This is hardware RAID 5? Because it's pretty screwy how this ends up | > | working when using software RAID and might take additional | > | troubleshooting. | > | > Yes, it's a Dell R710XD | > | > | > When installing CentOS 7 using the full disk capacity and booting in | > | > UEFI | > | > mode the machine dumps me into a GRUB rescue mode prompt. | > | > error: disk `,gpt2' not found | > | > Entering rescue mode... | > | > grub rescue> | > | | > | | > | This is confusing to me because there should be no such thing as grub | > | rescue on UEFI. On BIOS systems, there is boot.img (formerly stage 1) | > | and core.img in the MBR gap or on BIOS Boot if GPT disk (formerly | > | stage 1.5 and stage 2). The core.img is where grub rescue comes from | > | when it can't find grub modules, in particular normal.mod. | > | | > | But on UEFI, core.img, normal.mod, and a pile of other modules are all | > | baked into the grubx64.efi file founds on the EFI system partition. | > | | > | I suspect two things that can cause normal.mod to not be found: | > | a. The system is not in fact booting in UEFI mode and there's been | > | some mistake in the installation of grub. | > | b. The system is in UEFI mode, but either the installer, or | > | post-install, grub2-install was run which obliterates the grub2-efi | > | package installed grubx64.efi, i.e. it's not really proper to run | > | grub2-install on UEFI systems. | > | > I suspect this is the case. when attempting to run grub-install the system | > claims that the grub2-efi-modules packages aren't installed, so this may | > be an installer bug. | | What is attempting to run grub-install? Or even grub2-install? If the | installer is doing this, it's an installer bug. If the user is doing | it, it's user error. | | Also, you will need to check the NVRAM for stale values because | grub2-install also populates NVRAM with what will become the wrong | entry. You'll need to use 'efibootmgr -v' to get a listing to find the | bogus entry, which will be pointing to a path that includes | grubx64.efi, note the boot number and then do 'efibootmgr -b <bootnum> | -B' Where bootnum is the four digit value for the bogus entry. | | What should happen if there are no valid entries is shim.efi will work | with fallback.efi to create a proper NVRAM entry. The proper entry can | be found with the earlier grep efibootmgr command, and you can just | use that, while adding an additional \ for each \, so that it's \\. | NVRAM should point to shim.efi and it's shim.efi that loads the | prebaked grubx64.efi.
When running grub2-install from within recovery mode I can assure you it is not a user error because simply installing the grub2-efi-modules package allows for grub2-install to work. We will try the efibootmgr -v out too. -- James A. Peltier IT Services - Research Computing Group Simon Fraser University - Burnaby Campus Phone : 604-365-6432 Fax : 778-782-3045 E-Mail : jpelt...@sfu.ca Website : http://www.sfu.ca/itservices Twitter : @sfu_rcg Powering Engagement Through Technology _______________________________________________ CentOS mailing list CentOS@centos.org https://lists.centos.org/mailman/listinfo/centos
