On 09/16/2011 08:37 AM, Steve Clark wrote: > On 09/16/2011 08:10 AM, Jerry Geis wrote: >> On 09/16/2011 06:59 AM, Steve Clark wrote: >>> On 09/15/2011 06:03 PM, Jerry Geis wrote: >>>>> I think the fdisk in 6 tries to align on 4k boundaries. Does fdisk -c do >>>>> the >>>>> same thing? >>>>> >>>> Scott - thanks I just tried -cu and same result. >>>> >>>> jerry >>>> >>>> _______________________________________________ >>>> CentOS mailing list >>>> CentOS@centos.org >>>> http://lists.centos.org/mailman/listinfo/centos >>>> >>> have you tried sfdisk? >>> >>> >> Steve - I had not - but asking sfdisk to list the device on centos has >> the wrong geometry to start >> with just like fdisk does. it should be 255 heads and 63 sectors. >> >> sfdisk -v >> sfdisk (util-linux-ng 2.17.2) >> >> sfdisk -l /dev/sde >> >> Disk /dev/sde: 1022 cylinders, 247 heads, 62 sectors/track >> Warning: The partition table looks like it was made >> for C/H/S=*/255/63 (instead of 1022/247/62). >> For this listing I'll assume that geometry. >> Units = cylinders of 8225280 bytes, blocks of 1024 bytes, counting from 0 >> >> Device Boot Start End #cyls #blocks Id System >> /dev/sde1 * 0+ 974- 975- 7830616+ b W95 FAT32 >> end: (c,h,s) expected (974,221,63) found (1023,254,63) >> /dev/sde2 0 - 0 0 0 Empty >> /dev/sde3 0 - 0 0 0 Empty >> /dev/sde4 0 - 0 0 0 Empty >> >> >> ---------------- >> This is centos 5 >> sfdisk -v >> sfdisk (util-linux 2.13-pre7) >> >> sfdisk -l /dev/sdb >> >> Disk /dev/sdb: 974 cylinders, 255 heads, 63 sectors/track >> Units = cylinders of 8225280 bytes, blocks of 1024 bytes, counting from 0 >> >> Device Boot Start End #cyls #blocks Id System >> /dev/sdb1 * 0+ 851 852- 6843658+ 83 Linux >> /dev/sdb2 852 973 122 979965 82 Linux swap / Solaris >> /dev/sdb3 0 - 0 0 0 Empty >> /dev/sdb4 0 - 0 0 0 Empty >> >> > Hmm... > I have an automated script that installs C6 on devices - I have used > it on sata drives, ssds and > CF. The first thing I do is dd of=$DRIVE if=/dev/zero bs=1024 count=1 > to wipe out the existing > partition table then I do > > # 1MB = 2048 512byte sectors > DSIZE=`sfdisk -s -uS $DRIVE` > DSIZE=$((DSIZE*2)) > Log "DSIZE is $DSIZE" > #OFFSET=2048 > OFFSET=8 > SWAP=1000000 > BOOT=600000 > PSIZE=$(((DSIZE-(OFFSET+BOOT+SWAP+10))/2)) > PSIZE=$((PSIZE+(PSIZE%2))) > PSTART=$((PSIZE+BOOT+SWAP+OFFSET)) > Log "PSIZE is $PSIZE" > Log "PSTART is $PSTART" > # partition the disk for /boot, swap, / > #/sbin/sfdisk -q -uS $DRIVE << EOF > #8,600000,L,* > #,1000000,S > #,,L > #EOF > /sbin/sfdisk -f -q -uS $DRIVE << EOF > $OFFSET,$BOOT,L,* > $((OFFSET+BOOT)),$SWAP,S > $((OFFSET+BOOT+SWAP)),$PSIZE,L > $PSTART,,L > EOF > > I am creating two linux partitions and a swap partition. > The swap is fixed and the two linux partitions are approximately > equal. > I have had no problem booting C6 after doing this. > > Steve,
Thanks - I will try this script probably Monday - heading out today. Jerry _______________________________________________ CentOS mailing list CentOS@centos.org http://lists.centos.org/mailman/listinfo/centos