post your radvd.conf file, please. On Fri, Aug 24, 2012 at 6:23 PM, Richard Brown <[email protected]> wrote: > More testing... > > I can get sw10 to work (to hand out an IPv6 address), but my MacBook doesn't > get an IPv6 address when plugged into se00 (the wired interface). I have > appended the /etc/config/network file that I'm using. > > I get the same result if the last two lines are changed to: > > list adv_interface 'se00' > list adv_interface 'sw10' > > [To reprise, I'm trying to use the script at > http://www.bufferbloat.net/projects/cerowrt/wiki/IPv6_Tunnel to configure all > the HE.net tunnel parameters automatically. That script gives an error > "command failed: Device or resource busy (-16)" after it handles sw00 and > gw00, and then again after it does sw10 and gw10. I also get these errors > when I "/etc/init.d/network restart" with the config file below.] > > Any suggestions? Thanks. > > Rich Brown > Hanover, NH USA > > ======================================= > root@OpenWrt:~# cat /etc/config/network > > config interface 'loopback' > option ifname 'lo' > option proto 'static' > option ipaddr '127.0.0.1' > option netmask '255.0.0.0' > > config interface 'se00' > option ifname 'se00' > option proto 'static' > option ipaddr '172.30.42.1' > option netmask '255.255.255.224' > option ip6addr '2001:470:8a63:100::1/64' > > config interface 'ge00' > option ifname 'ge00' > option proto 'dhcp' > > config interface 'sw00' > option type 'none' > option proto 'static' > option ipaddr '172.30.42.65' > option netmask '255.255.255.224' > option ip6addr '2001:470:8a63:300::1/64' > > config interface 'sw10' > option type 'none' > option proto 'static' > option ipaddr '172.30.42.97' > option netmask '255.255.255.224' > option ip6addr '2001:470:8a63:200::1/64' > > config switch > option name 'rtl8366s' > option reset '1' > option enable_vlan '0' > option blinkrate '2' > option max_length '3' > > config switch_vlan > option device 'rtl8366s' > option vlan '1' > option ports '0 1 2 3 5t' > > config switch_port > option device 'rtl8366s' > option port '1' > option led '6' > > config switch_port > option device 'rtl8366s' > option port '2' > option led '9' > > config switch_port > option device 'rtl8366s' > option port '5' > option led '2' > > config interface 'gw00' > option type 'none' > option proto 'static' > option ipaddr '172.30.42.129' > option netmask '255.255.255.224' > option ip6addr '2001:470:8a63:400::1/64' > > config interface 'gw10' > option type 'none' > option proto 'static' > option ipaddr '172.30.42.161' > option netmask '255.255.255.224' > option ip6addr '2001:470:8a63:500::1/64' > > config interface 'gw01' > option proto 'ahcp' > option ip6addr '2001:470:8a63:600::1/64' > > config interface 'gw11' > option proto 'ahcp' > option ip6addr '2001:470:8a63:700::1/64' > > config interface 'henet' > option proto '6in4' > option peeraddr '209.51.161.14' > option ip6addr '2001:470:1f06:64::2/64' > option tunnelid 'dddddd' > option username 'YOUR-USERNAME' > option password 'YOUR-PASSWORD' > option adv_subnet '1' > option adv_interface 'se00' > option adv_interface 'sw10' > > > > _______________________________________________ > Cerowrt-devel mailing list > [email protected] > https://lists.bufferbloat.net/listinfo/cerowrt-devel
-- Dave Täht http://www.bufferbloat.net/projects/cerowrt/wiki - "3.3.8-17 is out with fq_codel!" _______________________________________________ Cerowrt-devel mailing list [email protected] https://lists.bufferbloat.net/listinfo/cerowrt-devel
