I dont see your "crypto isakmp nat-keepalive" statement. See
http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123tcr/123tsr/sec_c2gt.htm#wp1203839 Dave. Kristofer Sigurdsson wrote: > Hi list, > > I have a Cisco 1841 router, IOS 12.4(12), Adv. IP Services. I'm using it > for an EzVPN server where clients can VPN into a VRF which contains a local > network. Clients can connect and start to use eg. Remote Desktop to a > computer on the inside network, but as soon as some traffic starts flowing > (like opening a browser in Remote Desktop), the session hangs and, according > to the show crypto session remote <peer> detail, no new outbound (from the > VPN server) packets come and I start seeing dropped inbound packets > (dec'ed). Sample output: > > Crypto session current status > > Code: C - IKE Configuration mode, D - Dead Peer Detection > K - Keepalives, N - NAT-traversal, X - IKE Extended Authentication > > Interface: FastEthernet0/0 > Session status: UP-ACTIVE > Peer: x.x.x.x port 4406 fvrf: (none) ivrf: xx > Phase1_id: xxxx > Desc: (none) > IKE SA: local x.x.x.x/4500 remote x.x.x.x/4406 Active > Capabilities:CXN connid:233 lifetime:07:58:49 > IPSEC FLOW: permit ip 0.0.0.0/0.0.0.0 host 10.10.210.158 > Active SAs: 2, origin: dynamic crypto map > Inbound: #pkts dec'ed 279 drop 69 life (KB/Sec) 4587796/86332 > Outbound: #pkts enc'ed 432 drop 0 life (KB/Sec) 4587562/86332 > > Whatever the user tries to do on the VPN, the only thing that changes (apart > from time) is the dec'ed drop packets. The number of packets dec'ed/enc'ed > is not exactly consistant, but this always happens at the first burst of > data across the link. The counters go to a few hundred, then this happens. > The VPN connection stays up, nothing unusual in the client. It says > "transparent tunneling: active on UDP port 4500", so it probably doesn't > matter that the client is behind NAT, right? > > The problem only depends on data going over the link, not time. If I'm just > using ping, traceroute and SSH terminal access, there is no problem. As > soon as I put a burst on the link, it hangs and does not recover. We have a > few customers on the router, each using a different profile (pretty much > same configuration) and different VRFs for inside networks. Same problem > for all of them. > > Thanks in advance, > Kristo > > Here's the relevant configuration: > > aaa group server radius RADIUS-XX > server-private x.x.x.x auth-port 1645 acct-port 1646 key xxxxxxx > ip vrf forwarding xx > > aaa authentication login AAA-XX group RADIUS-XX > > aaa authorization network vpn local > > ip vrf xx > description xx > rd 65365:7 > route-target export 65365:7 > route-target import 65365:7 > ! > crypto isakmp policy 1 > encr 3des > hash md5 > authentication pre-share > group 2 > lifetime 28800 > ! > crypto isakmp policy 20 > encr 3des > authentication pre-share > group 5 > ! > crypto isakmp policy 30 > encr 3des > authentication pre-share > group 2 > ! > crypto isakmp client configuration group xxxx > key xxxxxxxxx > dns x.x.x.x > pool xx > acl xx > group-lock > save-password > max-users 50 > netmask 255.255.255.255 > ! > crypto isakmp profile xxxx > vrf xx > self-identity address > match identity group xxxx > client authentication list AAA-XX > isakmp authorization list vpn > client configuration address respond > initiate mode aggressive > local-address FastEthernet0/0 > ! > crypto ipsec security-association lifetime seconds 86400 > crypto ipsec security-association idle-time 86400 > ! > crypto ipsec transform-set vpn esp-3des esp-md5-hmac > ! > ! dynamic-map vpn 1-6 and 8-... are other customers who also have the same > problem > ! > crypto dynamic-map vpn 7 > set transform-set vpn > set isakmp-profile xxxx > reverse-route > ! > crypto map vpn 65535 ipsec-isakmp dynamic vpn > ! > interface FastEthernet0/0 > description Uplink > ip address x.x.x.x 255.255.255.128 > duplex auto > speed auto > crypto map vpn > ! > interface FastEthernet0/1.930 > encapsulation dot1Q 930 > ip vrf forwarding xx > ip address 10.9.8.2 255.255.255.252 > ! > ! The RIP is to advertise the host routes to the VPN clients to another > router on the inside (and receive routes from there) > ! > router rip > version 2 > ! > address-family ipv4 vrf xx > redistribute connected > redistribute static > network 10.0.0.0 > network 192.168.0.0 > network 192.168.124.0 > no auto-summary > version 2 > exit-address-family > ! > ip local pool xx 10.10.210.100 10.10.210.200 group xx > ! > ip access-list extended xx > (lots of networks) > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
