Ok Joe, thanks for all your help. Thanks, paul
P.A > -----Original Message----- P.A > From: Joe Maimon [mailto:[EMAIL PROTECTED] P.A > Sent: Wednesday, May 07, 2008 11:52 AM P.A > To: Paul A P.A > Cc: [email protected] P.A > Subject: Re: [c-nsp] mac address question P.A > P.A > To be correct they should be mac-addresses that can be guaranteed P.A > unique P.A > (such as off old ethernet nic's), but thats hard to do in a range. P.A > P.A > I dont see any reason to use different mac's for bridging and pppoe. P.A > P.A > P.A > P.A > P.A > P.A > Paul A wrote: P.A > > Joe, so basically I'm going to make up a mac-address and pass that P.A > along to P.A > > the Telco correct? P.A > > P.A > > Also currently im using a mac address on this router with RBE dsl P.A > > connections and the new DSL's getting cut over to this ATM are P.A > PPPOE, I read P.A > > somewhere on cisco that I should use a different mac-address for the P.A > PPPOE P.A > > under a bba-group. P.A > > P.A > > So I should just be able to make one up and pass that along to them? P.A > > P.A > > Thanks, P.A > > P.A > > Paul P.A > > P.A > > P.A > -----Original Message----- P.A > > P.A > From: Joe Maimon [mailto:[EMAIL PROTECTED] P.A > > P.A > Sent: Wednesday, May 07, 2008 10:50 AM P.A > > P.A > To: Paul A P.A > > P.A > Cc: [email protected] P.A > > P.A > Subject: Re: [c-nsp] mac address question P.A > > P.A > P.A > > P.A > Take an old ethernet card, copy its mac address and throw the P.A > ethernet P.A > > P.A > card out. P.A > > P.A > P.A > > P.A > Use that mac address. P.A > > P.A > P.A > > P.A > Realistically, the TELCO is actually asking for what to put in P.A > a layer P.A > > P.A > 2 P.A > > P.A > access list. P.A > > P.A > P.A > > P.A > You want to be able to connect multiple routers, for example P.A > with an P.A > > P.A > ATM P.A > > P.A > switch, so tell them a mac address with the last two hex P.A > digits masked P.A > > P.A > to FF P.A > > P.A > P.A > > P.A > That way you can connect a couple hundred routers without P.A > involving P.A > > P.A > them P.A > > P.A > again. P.A > > P.A > P.A > > P.A > So long as the mac's arent going to conflict with any of your P.A > > P.A > customers, P.A > > P.A > you shouldnt ever have a problem. P.A > > P.A > P.A > > P.A > P.A > > P.A > Paul A wrote: P.A > > P.A > > Hi, we have an ATM circuit that will be terminating some DSL P.A > > P.A > circuits. The P.A > > P.A > > Telco is asking me for the terminating router's mac address P.A > > P.A > > I'm confused as to what mac address I should give them. I P.A > know im P.A > > P.A > supposed P.A > > P.A > > to add the mac-address statement under the ATM interface P.A > according P.A > > P.A > to the P.A > > P.A > > documents I read on the cisco site but how go I figure out P.A > with mac P.A > > P.A > address P.A > > P.A > > to use? P.A > > P.A > > P.A > > P.A > > TIA, P P.A > > P.A > > P.A > > P.A > > P.A > > P.A > > _______________________________________________ P.A > > P.A > > cisco-nsp mailing list [email protected] P.A > > P.A > > https://puck.nether.net/mailman/listinfo/cisco-nsp P.A > > P.A > > archive at http://puck.nether.net/pipermail/cisco-nsp/ P.A > > P.A > > P.A > > P.A > > P.A > > P.A > > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
