Yes "mls mpls tunnel-recir" command is globally enabled. Supervisor and line cards are in PFC 3C/XL mode. I do not think routes are reaching over capacity of box.
Mod Ports Card Type Model Serial No. --- ----- -------------------------------------- ------------------ ----------- 1 5 Supervisor Engine 720 10GE (Active) VS-S720-10G 2 24 CEF720 24 port 1000mb SFP WS-X6724-SFP 3 8 CEF720 8 port 10GE with DFC WS-X6708-10GE 4 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX Mod MAC addresses Hw Fw Sw Status --- ---------------------------------- ------ ------------ ------------ ------- 1 0023.33ab.9b98 to 0023.33ab.9b9f 3.1 8.5(3) 12.2(33)SXI3 Ok 2 0026.cbb1.1c9c to 0026.cbb1.1cb3 4.1 12.2(18r)S1 12.2(33)SXI3 Ok 3 0025.84f0.dab8 to 0025.84f0.dabf 2.1 12.2(18r)S1 12.2(33)SXI3 Ok 4 0026.cbad.7d20 to 0026.cbad.7d4f 3.2 12.2(18r)S1 12.2(33)SXI3 Ok Mod Sub-Module Model Serial Hw Status ---- --------------------------- ------------------ ----------- ------- ------- 1 Policy Feature Card 3 VS-F6K-PFC3CXL 1.2 Ok 1 MSFC3 Daughterboard VS-F6K-MSFC3 2.0 Ok 2 Distributed Forwarding Card WS-F6700-DFC3CXL 1.6 Ok 3 Distributed Forwarding Card WS-F6700-DFC3CXL 1.6 Ok 4 Distributed Forwarding Card WS-F6700-DFC3CXL 1.6 Ok Mod Online Diag Status ---- ------------------- 1 Pass 2 Pass 3 Pass 4 Pass Krunal On Mon, Mar 15, 2010 at 12:35 PM, Peter Rathlev <pe...@rathlev.dk> wrote: > (I'm Cc:'ing the list again, since I'm sure many known this better than > me.) > > On Mon, 2010-03-15 at 12:04 -0400, krunal shah wrote: > > Yes we do. Command "show mls cef summary det" shows 300K of MPLS > > routes. Do not have a clue were these come from. My customer has a > > campus MPLS network with very little MPLS routes (<100, as displayed > > on all other MPLS nodes). Only this switch has some goofy thing > > > > 6500sw#show mls cef summary det > > > > Total routes: 616654 > > IPv4 unicast routes: 308336 > > IPv4 non-vrf routes: 99 > > IPv4 non-vrf routes (internal): 0 > > IPv4 vrf routes: 308223 > > IPv4 vrf routes (internal): 14 > > IPv4 Multicast routes: 8 > > MPLS routes: 308046 > > IPv6 unicast routes: 260 > > IPv6 non-vrf routes: 5 > > IPv6 non-vrf routes (internal): 0 > > IPv6 vrf routes: 0 > > IPv6 vrf routes (internal): 255 > > IPv6 multicast routes: 3 > > EoM routes: 1 > > Are you absolutely positive that this switch only has ~100 routes? The > above almost looks like it has a copy of the default-less routing table. > What does "show ip route summary" say? And "show ip bgp vpnv4 all > summary"? > > > 6500sw#show mls cef mpls (output left out) > > > > Index Local Label Out i/f > > Label Op > > > > 30088 82658(EOS) (-) recirc > > 30089 140839(EOS) (-) recirc > [...] > > - Does the switch have MPLS tunnel recirculation enabled? ("mls mpls > tunnel-recir" global config) > > - Have you exceeded the capacity of the box somehow? ("show platform > hardware capacity forwarding") > > - Maybe it's a non-XL PFC ("show module") with more than 192k/239k IPv4 > routes ("show mls cef maximum-routes")? > > -- > Peter > > > _______________________________________________ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/