Hello, Sorry to bother the list again with this !
Any ideas to might be going on ? Thanks. Y. 2010/6/2 Youssef Bengelloun-Zahr <[email protected]> > Hello again, > > I'm suspecting a misconfiguration between the terminal lines on the console > servers and the equipments, more specifically concerning baud rates. > > Here is an output of a show line on the console : > > CONS3.IX1#sh line 33 > > Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns > Int > 33 TTY 9600/9600 - - - - - 14 0 > 0/0 - > > > Line 33, Location: "", Type: "" > Length: 24 lines, Width: 80 columns > *Baud rate (TX/RX) is 9600/9600, no parity, 1 stopbits, 8 databits* > Status: Ready > Capabilities: EXEC Suppressed > Modem state: Ready > Modem hardware state: CTS noDSR DTR RTS > > Special Chars: Escape Hold Stop Start Disconnect Activation > ^Cx none - - none > Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch > never never none not set > Idle Session Disconnect Warning > never > Login-sequence User Response > 00:00:30 > Autoselect Initial Wait > not set > Modem type is unknown. > Session limit is not set. > Time since activation: never > > Editing is enabled. > History is enabled, history size is 10. > DNS resolution in show commands is enabled > Full user help is disabled > Allowed input transports are pad v120 telnet rlogin udptn ssh. > > Allowed output transports are pad v120 telnet rlogin ssh. > Preferred transport is telnet. > No output characters are padded > No special data dispatching characters > > > Here is an output of a show line cons0 on one of the core equipments : > > LNS1.IX1#sh line console 0 > > Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns > Int > 0 CTY - - - - - 0 1 > 0/0 - > > Line 0, Location: "", Type: "" > > Length: 24 lines, Width: 80 columns > *Baud rate (TX/RX) is 9600/9600, no parity, 1 stopbits, 0 databits* > Status: Ready, 0x40000 > Capabilities: none > Modem state: Ready > Group codes: 0 > > Special Chars: Escape Hold Stop Start Disconnect Activation > ^Cx none - - none > Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch > never never none not set > Idle Session Disconnect Warning > never > Login-sequence User Response > 00:00:30 > Autoselect Initial Wait > not set > Modem type is unknown. > Session limit is not set. > Time since activation: never > > Editing is enabled. > History is enabled, history size is 10. > DNS resolution in show commands is enabled > Full user help is disabled > Allowed input transports are none. > Allowed output transports are lat pad telnet rlogin mop v120 ssh nasi. > Preferred transport is none. > > No output characters are padded > No special data dispatching characters > > > It must some problem of this kind... Something so obvious that I'm not > seeing it. > > Thanks. > > > Y. > > > > 2010/6/2 Youssef Bengelloun-Zahr <[email protected]> > >> Hello, >> >> An interesting note on the following link : >> >> >> http://www.cisco.com/en/US/tech/tk801/tk36/technologies_configuration_example09186a008014f8e7.shtml >> >> >> *Note: *If you encounter authentication failures, remember that the >> terminal server performs the first authentication (if configured), while the >> device to which you try to connect performs the second authentication (if >> configured). Verify whether AAA is configured correctly on both the terminal >> server and the connecting device. >> >> >> Seems like it's the problem I am encountering here. >> >> I'll try to dig in this direction. >> >> Any help will be appreciated. >> >> Tx. >> >> Y. >> >> >> >> 2010/6/2 Youssef Bengelloun-Zahr <[email protected]> >> >> Hello, >>> >>> Yes, it is configured on both cons1 and 2 : >>> >>> >>> line 33 64 >>> exec-timeout 0 0 >>> no exec >>> transport input telnet >>> >>> escape-character 3 >>> stopbits 1 >>> >>> >>> Here is an output of a show line xx on the console routers : >>> >>> CONS1.IX1#sh line 33 >>> Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise >>> Overruns Int >>> 33 TTY 9600/9600 - - - - - 0 10668 >>> 4/10 - >>> >>> Line 33, Location: "", Type: "" >>> Length: 24 lines, Width: 80 columns >>> *Baud rate (TX/RX) is 9600/9600, no parity, 1 stopbits, 8 databits* >>> *Status: Ready* >>> *Capabilities: EXEC Suppressed* >>> Modem state: Ready >>> Modem hardware state: CTS* DSR DTR RTS >>> Special Chars: Escape Hold Stop Start Disconnect Activation >>> ^Cx none - - none >>> Timeouts: Idle EXEC Idle Session Modem Answer Session >>> Dispatch >>> never never none not >>> set >>> Idle Session Disconnect Warning >>> never >>> Login-sequence User Response >>> 00:00:30 >>> Autoselect Initial Wait >>> not set >>> Modem type is unknown. >>> Session limit is not set. >>> Time since activation: 00:00:01 >>> Editing is enabled. >>> History is enabled, history size is 10. >>> DNS resolution in show commands is enabled >>> Full user help is disabled >>> Allowed input transports are telnet. >>> Allowed output transports are pad v120 telnet rlogin ssh. >>> Preferred transport is telnet. >>> No output characters are padded >>> No special data dispatching characters >>> >>> >>> Y. >>> >>> >>> >>> 2010/6/2 Ian Henderson <[email protected]> >>> >>> On Wed, 2 Jun 2010, Youssef Bengelloun-Zahr wrote: >>>> >>>> User-Name = *"CONS2.IX1> ### Login failed"* >>>>> >>>> >>>> Do you have 'no exec' configured under the async line stanza on CONS1 >>>> and CONS2? The config you posted is for CONS3, which does have it >>>> configured. >>>> >>>> >>>> line 33 64 >>>>> exec-timeout 0 0 >>>>> no exec >>>>> transport input all >>>>> escape-character 3 >>>>> stopbits 1 >>>>> >>>> >>>> Rgds, >>>> >>>> >>>> - I. >>>> >>> >>> >>> >>> -- >>> Youssef BENGELLOUN-ZAHR ……………………………………………… >>> Ingénieur Réseaux et Télécoms >>> >>> >>> Technopole de l'Aube en Champagne - BP 601 - 10901 TROYES Cedex 9 >>> Agence Paris : 6, rue Charles Floquet - 92120 MONTROUGE >>> Tel +33 (0) 825 000 720 >>> Tel. direct +33 (0) 1 77 35 59 14 >>> Tel. portable +33 (0) 6 22 42 63 80 >>> Email [email protected] >>> ……………………………………………………………………………….....www.720.fr >>> >>> >> >> >> -- >> Youssef BENGELLOUN-ZAHR ……………………………………………… >> Ingénieur Réseaux et Télécoms >> >> >> Technopole de l'Aube en Champagne - BP 601 - 10901 TROYES Cedex 9 >> Agence Paris : 6, rue Charles Floquet - 92120 MONTROUGE >> Tel +33 (0) 825 000 720 >> Tel. direct +33 (0) 1 77 35 59 14 >> Tel. portable +33 (0) 6 22 42 63 80 >> Email [email protected] >> ……………………………………………………………………………….....www.720.fr >> >> > > > -- > Youssef BENGELLOUN-ZAHR ……………………………………………… > Ingénieur Réseaux et Télécoms > > > Technopole de l'Aube en Champagne - BP 601 - 10901 TROYES Cedex 9 > Agence Paris : 6, rue Charles Floquet - 92120 MONTROUGE > Tel +33 (0) 825 000 720 > Tel. direct +33 (0) 1 77 35 59 14 > Tel. portable +33 (0) 6 22 42 63 80 > Email [email protected] > ……………………………………………………………………………….....www.720.fr > > -- Youssef BENGELLOUN-ZAHR ……………………………………………… Ingénieur Réseaux et Télécoms Technopole de l'Aube en Champagne - BP 601 - 10901 TROYES Cedex 9 Agence Paris : 6, rue Charles Floquet - 92120 MONTROUGE Tel +33 (0) 825 000 720 Tel. direct +33 (0) 1 77 35 59 14 Tel. portable +33 (0) 6 22 42 63 80 Email [email protected] ……………………………………………………………………………….....www.720.fr _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
