XYZ01-exacc-rtr01#show inventory | I SPA NAME: "module 0", DESCR: "Cisco ASR1000 SPA Interface Processor 10" NAME: "SPA subslot 0/0", DESCR: "5-port Gigabit Ethernet Shared Port Adapter" PID: SPA-5X1GE-V2 , VID: V02, SN: JAE1139YA4X NAME: "SPA subslot 0/1", DESCR: "8-port Channelized T1/E1 to DS0 Shared Port Adapter" PID: SPA-8XCHT1/E1 , VID: V05, SN: JAE1344MT1W NAME: "SPA subslot 0/2", DESCR: "4-port T3/E3 Serial Shared Port Adapter" PID: SPA-4XT3/E3 , VID: V02, SN: JAE1343LZZ8 NAME: "SPA subslot 0/3", DESCR: "4-port OC3/STM1 POS Shared Port Adapter" PID: SPA-4XOC3-POS , VID: V01, SN: JAE13020E52
XYZ01-exacc-rtr01#show run | I card type card type t1 0 1 card type t3 0 2 John -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Renelson Panosky Sent: Thursday, September 30, 2010 2:26 PM To: Mack O'Brian Cc: [email protected] Subject: Re: [c-nsp] ASR1006 Router No, That's not it. that's for the 3800 and 3900 series On Thu, Sep 30, 2010 at 2:57 PM, Mack O'Brian <[email protected]>wrote: > I believe it is card type command. > > config t#card type t3 0 3 > > > > On Thu, Sep 30, 2010 at 11:50 AM, Renelson Panosky < > [email protected]> wrote: > >> I am configuring an ASR1006 with the following SPA cards installed. >> >> SPA-10X1GE-V2 >> SPA-4XT3/E3 >> SPA-8XCHT1/E1 >> >> Do anybody know the command to type to make the router recognize the >> following cards ? >> >> SPA-4XT3/E3 >> SPA-8XCHT1/E1 >> >> Because when i do sho ip int brief >> >> i only see the following >> >> Interface IP-Address OK? Method Status >> Protocol >> GigabitEthernet0/1/0 unassigned YES unset administratively down >> down >> GigabitEthernet0/1/1 unassigned YES unset administratively down >> down >> GigabitEthernet0/1/2 unassigned YES unset administratively down >> down >> GigabitEthernet0/1/3 unassigned YES unset administratively down >> down >> GigabitEthernet0/1/4 unassigned YES unset administratively down >> down >> GigabitEthernet0/1/5 unassigned YES unset administratively down >> down >> GigabitEthernet0/1/6 unassigned YES unset administratively down >> down >> GigabitEthernet0/1/7 unassigned YES unset administratively down >> down >> GigabitEthernet0/1/8 unassigned YES unset administratively down >> down >> GigabitEthernet0/1/9 unassigned YES unset administratively down >> down >> GigabitEthernet0 unassigned YES unset administratively down >> down >> >> >> However, when i do a sho log i can see them. Please help! >> _______________________________________________ >> cisco-nsp mailing list [email protected] >> https://puck.nether.net/mailman/listinfo/cisco-nsp >> archive at http://puck.nether.net/pipermail/cisco-nsp/ >> > > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
