On Mon, 15 Nov 2010 13:51:49 +0100, "Brian Turnbow" <b.turn...@twt.it> wrote: > Hi Marco > > See inline > >> -----Original Message----- >> From: cisco-nsp-boun...@puck.nether.net [mailto:cisco-nsp- >> boun...@puck.nether.net] On Behalf Of Marco Marzetti >> Sent: lunedì 15 novembre 2010 10:36 >> To: cisco-nsp@puck.nether.net >> Subject: [c-nsp] SIP to ISDN Call Progress >> >> >> Hello, >> >> I have a problem with SIP to ISDN internetworking on Cisco IOS. >> I'm unable to receive early-media messages from the ISDN side of the >> call. >> Hardware and software versions are: Cisco 2800 Software >> (C2800NM-ENTSERVICES-M), Version 12.4(20)T6, RELEASE SOFTWARE (fc2). >> >> # debug isdn q931 int Se0/1/0:15 >> Nov 15 10:06:54.437 CET: ISDN Se0/1/0:15 Q931: Applying typeplan for >> sw-type 0x12 is 0x0 0x1, Calling num 03631970XXX >> Nov 15 10:06:54.441 CET: ISDN Se0/1/0:15 Q931: Sending SETUP callref = >> 0x0D0D callID = 0x980D switch = primary-net5 interface = User >> Nov 15 10:06:54.441 CET: ISDN Se0/1/0:15 Q931: TX -> SETUP pd = 8 >> callref >> = 0x0D0D >> Bearer Capability i = 0x8090A3 >> Standard = CCITT >> Transfer Capability = Speech >> Transfer Mode = Circuit >> Transfer Rate = 64 kbit/s >> Channel ID i = 0xA9839F >> Exclusive, Channel 31 >> Calling Party Number i = 0x0180, '03631970XXX' >> Plan:ISDN, Type:Unknown >> Called Party Number i = 0x81, '199151119' >> Plan:ISDN, Type:UnknownsipSPIUpdateRtcpSession: sx79861: >> started RTP >> timer in state STATE_SENT_ALERTING >> >> Nov 15 10:06:54.457 CET: ISDN Se0/1/0:15 Q931: RX <- SETUP_ACK pd = 8 >> callref = 0x8D0D >> Channel ID i = 0xA9839F >> Exclusive, Channel 31 >> >> >> Nov 15 10:06:56.745 CET: ISDN Se0/1/0:15 Q931: RX <- CALL_PROC pd = 8 >> callref = 0x8D0D > > > There is no progress indicator indicating that inband information is now > available. > So no opening of the audio channel. You can play around with the progress > indicators you send out with your setup to manipulate this > Try searching for no ringback , no busytones on the cisco website for an > in depth explanation. > >
Hello, I configured my dial-peer in this way: dial-peer voice 1400 pots voice cut-through alert preference 4 destination-pattern 199151119 progress_ind setup enable 1 no digit-strip port 0/0/1:15 ! Now i see the PI reminder: Nov 15 14:39:07.121 CET: ISDN Se0/1/0:15 Q931: TX -> SETUP pd = 8 callref = 0x1C5C Bearer Capability i = 0x8090A3 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA9839F Exclusive, Channel 31 Progress Ind i = 0x8181 - Call not end-to-end ISDN, may have in-band info Calling Party Number i = 0x0180, '03631970353' Plan:ISDN, Type:Unknown Called Party Number i = 0x81, '199151119' Plan:ISDN, Type:Unknown Nov 15 14:39:07.133 CET: ISDN Se0/1/0:15 Q931: RX <- SETUP_ACK pd = 8 callref = 0x9C5C Channel ID i = 0xA9839F Exclusive, Channel 31 Nov 15 14:39:08.253 CET: ISDN Se0/1/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x9C5C Looking at this: http://www.cisco.com/en/US/tech/tk1077/technologies_tech_note09186a0080094c33.shtml#progresstones I would expect the call to be cutted-throug after the SETUP_ACK has been received. Anyway I have the same problem, no audio i sent to my phone before the CONNECT message. Thank You _______________________________________________ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/