Good morning, I need to insert a route in the general routing table and in a VRF.
Reading on Internet, I thought to use ip vrf receive command on the interface. this is CS router : hostname CS ! boot-start-marker boot-end-marker ! ip cef ! ! ! ! ip vrf VTC ! interface Loopback1021030 ip vrf receive VTC ip address 10.210.3.1 255.255.255.255 ip policy route-map PC_TO_VTC ! interface FastEthernet0/0 no ip address duplex auto speed auto ! interface FastEthernet0/1 ip vrf receive VTC ip address 10.210.0.6 255.255.255.252 ip policy route-map PC_TO_VTC speed auto full-duplex ! ! ! ip forward-protocol nd ip route vrf VTC 10.208.0.0 255.255.255.0 10.210.0.5 ! ! no ip http server no ip http secure-server ! access-list 100 permit ip 10.210.3.0 0.0.0.255 10.208.0.0 0.0.0.255 access-list 100 permit ip 10.208.0.0 0.0.0.255 10.210.3.0 0.0.0.255 access-list 100 permit ip 10.210.0.0 0.0.0.255 10.208.0.0 0.0.0.255 access-list 100 permit ip 10.208.0.0 0.0.0.255 10.210.0.0 0.0.0.255 ! route-map PC_TO_VTC permit 1 match ip address 100 set vrf VTC !!!!!!!!!!!!!!!!!!!!!!!!!!!!! and this is border router : hostname Border_VTC ! boot-start-marker boot-end-marker ! ! no aaa new-model ip cef ip vrf VTC interface Loopback1 ip vrf forwarding VTC ip address 10.208.0.1 255.255.255.255 ! interface FastEthernet0/0 ip vrf forwarding VTC ip address 10.210.0.2 255.255.255.252 duplex auto speed auto ! interface FastEthernet0/1 ip vrf forwarding VTC ip address 10.210.0.5 255.255.255.252 speed auto full-duplex ip forward-protocol nd ip route vrf VTC 10.210.3.0 255.255.255.0 10.210.0.6 ! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Trying to ping I have CS#ping vrf VTC 10.208.0.1 source fastEthernet 0/1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.208.0.1, timeout is 2 seconds: Packet sent with a source address of 10.210.0.6 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/100/189 ms CS# *Mar 1 00:08:13.404: ICMP: echo reply rcvd, src 10.208.0.1, dst 10.210.0.6 *Mar 1 00:08:13.593: ICMP: echo reply rcvd, src 10.208.0.1, dst 10.210.0.6 *Mar 1 00:08:13.673: ICMP: echo reply rcvd, src 10.208.0.1, dst 10.210.0.6 *Mar 1 00:08:13.749: ICMP: echo reply rcvd, src 10.208.0.1, dst 10.210.0.6 *Mar 1 00:08:13.813: ICMP: echo reply rcvd, src 10.208.0.1, dst 10.210.0.6 CS#ping vrf VTC 10.208.0.1 source Loopback1021030 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.208.0.1, timeout is 2 seconds: Packet sent with a source address of 10.210.3.1 ..... On this failed ping i get Border_VTC# *Mar 1 00:08:33.810: ICMP: echo reply sent, src 10.208.0.1, dst 10.210.3.1 *Mar 1 00:08:35.757: ICMP: echo reply sent, src 10.208.0.1, dst 10.210.3.1 *Mar 1 00:08:37.764: ICMP: echo reply sent, src 10.208.0.1, dst 10.210.3.1 *Mar 1 00:08:39.752: ICMP: echo reply sent, src 10.208.0.1, dst 10.210.3.1 *Mar 1 00:08:41.767: ICMP: echo reply sent, src 10.208.0.1, dst 10.210.3.1 Trying ping on other router i get Border_VTC#ping vrf VTC 10.210.3.1 source fastEthernet 0/1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.210.3.1, timeout is 2 seconds: Packet sent with a source address of 10.210.0.5 ..... Success rate is 0 percent (0/5) Border_VTC#ping vrf VTC 10.210.3.1 source loopback 1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.210.3.1, timeout is 2 seconds: Packet sent with a source address of 10.208.0.1 ..... Success rate is 0 percent (0/5) Border_VTC# Any suggestion ? -- L. _______________________________________________ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/