Hi all, Hoping someone can test this for me, I believe there is a severe bug with IPv6 on the ASR.
We are unable to stand up IPv6 in the following scenario: ASR - Gi0/0/0 connected to a trunk port on a Catalyst, and another trunk port connected to Gi0/0 on an ISR2911 If you configure the following on the ASR: interface GigabitEthernet0/0/0.4010 encapsulation dot1Q 4010 ip address 192.168.1.1 255.255.255.0 ipv6 address FDC3:76E6:F4EF:2A24::2/64 ipv6 enable end The configure the following on the 2911 (or any ISR with IPv6 support): interface GigabitEthernet0/0.4010 encapsulation dot1Q 4010 ip address 192.168.1.2 255.255.255.0 ipv6 address FDC3:76E6:F4EF:2A24::1/64 ipv6 enable end On the Catalyst set the ports your Gi0/0/0 and Gi0/0 are connected to to trunk mode and allow all VLAN's. ISR#ping FDC3:76E6:F4EF:2A24::1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FDC3:76E6:F4EF:2A24::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/0 ms ISR1#ping FDC3:76E6:F4EF:2A24::2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FDC3:76E6:F4EF:2A24::2, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) So we confirm the router can ping itself (so IPv6 is enabled), but it can't ping the other end of the link. Nothing in neighbours either. ASR#ping FDC3:76E6:F4EF:2A24::2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FDC3:76E6:F4EF:2A24::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms ASR#ping FDC3:76E6:F4EF:2A24::1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FDC3:76E6:F4EF:2A24::1, timeout is 2 seconds: .H..H Success rate is 0 percent (0/5) Ditto on the ASR. Two ISR's work fine. Code I'm using: ASR: asr1001-universalk9.03.07.00b.S.152-4.S0b.bin ISR: c2900-universalk9-mz.SPA.152-1.T1.bin I've had a case open with TAC for 7 days now and they still can't resolve it... Hopefully someone has some spare kit to test this on. -Scott ________________________________ The content of this message and any attachments may be privileged, confidential or sensitive. Any unauthorised used is prohibited. Views expressed in this message are those of the individual sender, except where stated otherwise with appropriate authority. All pricing provided is valid at the time of writing only and due to factors such as the exchange rate, may change without notice. Sales are made subject to our Terms & Conditions, available at http://www.end2end.co.nz/info/ ________________________________ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
