Ain't no deep magic there.  What were you /hoping/ would happen ?


c2610#connect 198.15.14.5
Trying 198.15.14.5 ... Open

UNIX(r) System V Release 4.0 (tony3)

login: 


(BTW, this box *isn't* on the Internet, so don't bother trying...)

Tone

> From: cisco cabanaboy [mailto:[EMAIL PROTECTED]]

> C2600-REG4-1#
> C2600-REG4-1#conf t
> Enter configuration commands, one per line.  End with
> CNTL/Z.
> C2600-REG4-1(config)#connect ?
>   WORD  Name for this connection
> 
> C2600-REG4-1(config)#connect bla ?
> % Unrecognized command
> C2600-REG4-1(config)#connect bla
> 
> 
> 
> 
> --- Chuck Larrieu <[EMAIL PROTECTED]> wrote:
> > Beats me. Routers are down. Any hint is you do a
> > connect ? what is the
> > output there?
> > 
> > Chuck
> > 
> > -----Original Message-----
> > From:       [EMAIL PROTECTED]
> > [mailto:[EMAIL PROTECTED]] On Behalf Of
> > cisco cabanaboy
> > Sent:       Wednesday, May 31, 2000 1:02 PM
> > To: [EMAIL PROTECTED]
> > Subject:
> > 
> > what is the global config command "connect" for ?
> > 
> > C2600-REG4-1(config)#?
> > Configure commands:
> > ....
> > connect                     cross-connect two
> > interfaces
> > controller                  Configure a specific
> > controller
> > default                     Set a command to its
> > defaults
> > default-value               Default character-bits
> > values
> > dial-control-mib            Define Dial Control Mib
> > parameters
> > dial-peer                   Dial Map (Peer)
> > configuration commands
> > dialer                      Dialer commands
> > dialer-list                 Create a dialer list
> > entry
> > dlsw                        Data Link Switching
> > global
> > configuration commands
> > dnsix-dmdp                  Provide DMDP service for
> > DNSIX
> > dnsix-nat                   Provide DNSIX service
> > for
> > audit trails
> > downward-compatible-config  Generate a configuration
> > compatible with older
> >                             software
> > dspu                        DownStream Physical Unit
> > Command
> > enable                      Modify enable password
> > parameters
> > end                         Exit from configure mode
> > endnode                     SNA APPN endnode command
> > exception                   Exception handling
> > exit                        Exit from configure mode
> > 
> > =====
> > ciscocabanaboy, CCNP-Voice, CCDP, MCSE, CNX, A+, N+,
> > I-net+, BOFH...
> > 
> > __________________________________________________
> > Do You Yahoo!?
> > Send instant messages & get email alerts with Yahoo!
> > Messenger.
> > http://im.yahoo.com/
> > 
> > ___________________________________
> > UPDATED Posting Guidelines:
> > http://www.groupstudy.com/list/guide.html
> > FAQ, list archives, and subscription info:
> > http://www.groupstudy.com
> > Report misconduct and Nondisclosure violations to
> > [EMAIL PROTECTED]
> > 
> 
> 
> =====
> ciscocabanaboy, CCNP-Voice, CCDP, MCSE, CNX, A+, N+, I-net+, BOFH...
> 
> __________________________________________________
> Do You Yahoo!?
> Send instant messages & get email alerts with Yahoo! Messenger.
> http://im.yahoo.com/
> 
> ___________________________________
> UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
> FAQ, list archives, and subscription info: http://www.groupstudy.com
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
> 

___________________________________
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives, and subscription info: http://www.groupstudy.com
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]

Reply via email to