url do a no shut on serial intf clock dce say 64000 then sh controllers ser x
Look at the DCD=up DSR=up DTR=up RTS=up CTS=up you have a working cable, interface 2x http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fint er_r/irfshoap.htm#1019003 http://www.cisco.com/en/US/tech/tk713/tk507/technologies_configuration_examp le09186a0080094504.shtml LET OP DE ONDERSTE REGEL DAN IS IE UP! spicey#show interfaces serial 1 Serial1 is up, line protocol is up Hardware is HD64570 Internet address is 5.0.2.2/24 MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation PPP, loopback not set Keepalive set (10 sec) LCP Open Open: IPCP Last input 00:00:01, output 00:00:01, output hang never Last clearing of "show interface" counters 00:09:27 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 130 packets input, 3392 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 129 packets output, 3378 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up Martijn -----Oorspronkelijk bericht----- Van: Jansen, M Verzonden: vrijdag 8 augustus 2003 12:36 Aan: 'LINSEN Jurgen (BMB)'; [EMAIL PROTECTED] Onderwerp: RE: cisco back to back cable [7:71992] In dutch, to keep things easy. Denk dat je eerst even de zaken moet proberen. controle kabel checken met commando sh controller serial, zie je een interface type staan, dus die dce/dte sh interface serial x Router# show interfaces serial Serial 0 is up, line protocol is up Hardware is MCI Serial Internet address is 131.136.190.203, subnet mask is 255.255.255.0 MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 255/255, load 1/255 Encapsulation HDLC, loopback not set, keepalive set (10 sec) Last input 0:00:07, output 0:00:00, output hang never Output queue 0/40, 0 drops; input queue 0/75, 0 drops Five minute input rate 0 bits/sec, 0 packets/sec Five minute output rate 0 bits/sec, 0 packets/sec 16263 packets input, 1347238 bytes, 0 no buffer Received 13983 broadcasts, 0 runts, 0 giants 2 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 2 abort 1 carrier transitions 22146 packets output, 2383680 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets, 0 restarts check onderaan dte/dce/rts/cts signalen moeten werken configuratie standaard configuratie de ene is dce (moet commando clockrate bv 64000 bij) ander is dte geen clockrate Martijn -----Oorspronkelijk bericht----- Van: LINSEN Jurgen (BMB) [mailto:[EMAIL PROTECTED] Verzonden: vrijdag 8 augustus 2003 9:37 Aan: [EMAIL PROTECTED] Onderwerp: RE: cisco back to back cable [7:71992] Sure you're using a cross cable? -----Original Message----- From: KW S [mailto:[EMAIL PROTECTED] Sent: Monday, July 07, 2003 6:22 PM To: [EMAIL PROTECTED] Subject: cisco back to back cable [7:71992] Dear All I have a 2501 and 2505 and I am trying to set up a homelab..These 2 routers come with a cable which is a DB60(DTE) and the other end is a DB60(DCE).This is wat that is label on the cable. Anyway, I try to connect this cable to the serial interface of the 2 routers...and both the routers are showing serial is down and line protocol is down. I guess I have used the wrong cable...or maybe I have missed out something. Please comment.. Regards, kws **** DISCLAIMER **** "This e-mail and any attachment thereto may contain information which is confidential and/or protected by intellectual property rights and are intended for the sole use of the recipient(s) named above. Any use of the information contained herein (including, but not limited to, total or partial reproduction, communication or distribution in any form) by other persons than the designated recipient(s) is prohibited. If you have received this e-mail in error, please notify the sender either by telephone or by e-mail and delete the material from any computer". Thank you for your cooperation. For further information about Proximus mobile phone services please see our website at http://www.proximus.be or refer to any Proximus agent. **Please support GroupStudy by purchasing from the GroupStudy Store: http://shop.groupstudy.com FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=73714&t=73714 -------------------------------------------------- **Please support GroupStudy by purchasing from the GroupStudy Store: http://shop.groupstudy.com FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
