Hi there
Yes , I have changed the priority to the lowest of all the switches .
Set spanning-tree priority 30000
Then the cost is 0 for that switch .
Is there any other commands ?
Thx
Olden Pieterse
Pre-Sales Consultant
Westcon
Tel: +27 21 415 7211
Fax: +27 21 419 7537
Mobile: +27 82 564 0709
Email: [EMAIL PROTECTED]
Web: http://www.westcon.co.za <http://www.westcon.co.za>
Remember, our product range includes:
3Com, Addtron, APC, IMC, Cisco, Extreme, Lucent, Motorola, Nortel-Networks
and Ramp.
E-mail Disclaimer:
Any email message from a WESTCON employee, and all attached thereto ("the
message") may contain confidential information, and is intended for a
specific addressee and purpose. If you are not the addressee
* you may not use, disclose, copy, distribute, retransmit, review,
disseminate or take any action based on the contents thereof;
* kindly inform the sender immediately and destroy all copies thereof.
Any copying, publication, dissemination, retransmission or
disclosure of this message, or part thereof, in any form whatsoever, without
the sender's expressed written consent, is prohibited. No opinion expressed
or implied by the sender necessarily constitutes the opinion of WESTCON.
This message does not constitute a guarantee or proof of the facts mentioned
therein. WESTCON accepts no responsibility or liability in respect of:-
* any opinion or guarantee of fact, whether expressed or implied; or
any action or failure to act as a result of any information contained in
this message, unless such information or opinion has been confirmed in
writing by an authorised WESTCON director.
-----Original Message-----
From: [EMAIL PROTECTED] [SMTP:[EMAIL PROTECTED]]
Sent: 19 September 2000 05:59
To: [EMAIL PROTECTED]
Subject: RE: broadcast storms
The first thing I would do is to make sure that the 6509 in the
center of
the whole network is set as the root for all VLANS. This will help
tremendously.
-----Original Message-----
From: Olden Pieterse [mailto:[EMAIL PROTECTED]]
Sent: Tuesday, September 19, 2000 10:16 AM
To: 'Groupstudy'
Subject: broadcast storms
Hi there gang
A question plse....
We are busy installing a sizable switch network .
Loads of 35XX and one 6509 . Gig fibres running in a star topology
from the
6509 to the 35XX's .
On some of the floors there are redundant UTP between the switches .
Spanning tree is on and igmp is enabled on the 6509 .
Why is there still loops & broadcast storms ? There is a load of IPX
& IP .
Topology changes seems to bog the 6509 down .
It even froze at stages .
Some advice or pointers would be very helpful .
Please include my email in your reply .
Cheers
Olden Pieterse
Pre-Sales Consultant
Westcon
Tel: +27 21 415 7211
Fax: +27 21 419 7537
Mobile: +27 82 564 0709
Email: [EMAIL PROTECTED]
Web: http://www.westcon.co.za <http://www.westcon.co.za>
Remember, our product range includes:
3Com, Addtron, APC, IMC, Cisco, Extreme, Lucent, Motorola,
Nortel-Networks
and Ramp.
E-mail Disclaimer:
Any email message from a WESTCON employee, and all attached thereto
("the
message") may contain confidential information, and is intended for
a
specific addressee and purpose. If you are not the addressee
* you may not use, disclose, copy, distribute, retransmit,
review,
disseminate or take any action based on the contents thereof;
* kindly inform the sender immediately and destroy all copies
thereof.
Any copying, publication, dissemination, retransmission or
disclosure of this message, or part thereof, in any form whatsoever,
without
the sender's expressed written consent, is prohibited. No opinion
expressed
or implied by the sender necessarily constitutes the opinion of
WESTCON.
This message does not constitute a guarantee or proof of the facts
mentioned
therein. WESTCON accepts no responsibility or liability in respect
of:-
* any opinion or guarantee of fact, whether expressed or
implied; or
any action or failure to act as a result of any information
contained in
this message, unless such information or opinion has been confirmed
in
writing by an authorised WESTCON director.
**NOTE: New CCNA/CCDA List has been formed. For more information go
to
http://www.groupstudy.com/list/Associates.html
_________________________________
UPDATED Posting Guidelines:
http://www.groupstudy.com/list/guide.html
FAQ, list archives, and subscription info: http://www.groupstudy.com
Report misconduct and Nondisclosure violations to
[EMAIL PROTECTED]
**NOTE: New CCNA/CCDA List has been formed. For more information go to
http://www.groupstudy.com/list/Associates.html
_________________________________
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives, and subscription info: http://www.groupstudy.com
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
