Nod,
checked all that stuff. I mean the serial port is the same one i use for
other routers. I think my CSC/4 may be bad. Even though led's don't lead
me to believe that.
You say yours arrives tommorow, what config did you get? these routers
are LOUD!
Brian
On Mon, 30 Oct 2000, Cthulu, CCIE Candidate wrote:
> OK,
>
> My AGS+ arrives tomorrow; offhand, not having all the information does not
> prevent me from shooting off my mouth so here goes:
>
> >From Cisco:
>
> Either the console port or the auxiliary port must be connected to an
> asynchronous device in order to communicate with the AGS+.
>
> The console port is a female, data communications equipment (DCE), DB-25
> receptacle for connecting an ASCII terminal. Before you connect the console
> port, set up the terminal as follows: 9600 baud, 8 data bits, no parity, and
> 2 stop bits.
>
> The optional auxiliary port is a male, data terminal equipment (DTE), DB-25
> receptacle for connection to a modem or other DCE device (such as a CSU/DSU
> or another router).
>
>
> Now if that doesn't work, upgrade your hyperterminal, and also ensure that
> the serial port you are using not being used by anything else (check to
> ensure that your OS also knows this).
>
> If that doesn't work:
>
> Put one of those db-25 to rj45 cisco modem adapters on the console port on
> the ags+ if you got one. Then connect an roll over cable to your pc's rj45
> serial adapter thingie. Then use the normal 9600n18 settings you use for
> the other routers.
>
>
> If that doesnt work, remove all cards, cuss, then firmly reseat them. Also,
> check your jumpers to ensure you have the console settings you think you
> have.
>
> See
> http://www.cisco.com/univercd/cc/td/doc/product/core/cisagspl/agscfig/43494.
> htm#xtocid281935
>
>
> I think the AGS+ is a product of Satan and Cisco, but it makes a damned fine
> frame relay switch if you don't mind going deaf from teh fans...
>
>
> Charles
>
>
>
>
>
> "Brian" <[EMAIL PROTECTED]> wrote in message
> [EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> >
> > I got an AGS+ in today and I am having trouble making a console connection
> > to it. I am an expert in the AGS+ and could really use some help.
> >
> > The CSC-MC+ is green. It has the 20pin connection to the ENV card.
> > The CSC-ENV is green. It has the 20pin connection to the CSC-MC+,
> > it also has the 4 pin "control" connection as well.
> > The CSC/4 is green, the console cable is connected properly.
> >
> > I am using a normal serial cable, 8/n/1 9600. The config register on the
> > CSC/4 is at factory default (pins 2 and 9 jumped).
> >
> > I have removed all other cards until I can get the console. Any ideas?
> >
> > Thanks,
> >
> > Brian
> >
> >
> > -----------------------------------------------
> > Brian Feeny, CCNP, CCDP [EMAIL PROTECTED]
> > Network Administrator
> > ShreveNet Inc. (ASN 11881)
> >
> > _________________________________
> > FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
> >
>
>
> _________________________________
> FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
-----------------------------------------------
Brian Feeny, CCNP, CCDP [EMAIL PROTECTED]
Network Administrator
ShreveNet Inc. (ASN 11881)
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
