[EMAIL PROTECTED] wrote:
>
> Carmelo
> If you are using both serials. Are they in the expansion slot or in
> the WAN slots. If you have a spare WAN slot you could use a WIC 2 T to give
> you 2 high speed ports.
>
> How have you got the 4 ISDN ports into the router ?
He got it with 4 port ISDN-BRI network module (NM-4B-...)
NM-4B-S/T 4-Port ISDN-BRI Network Module
NM-4B-S/T= 4-Port ISDN-BRI Network Module
NM-4B-U 4-Port ISDN-BRI with NT-1 Network Module
NM-4B-U= 4-Port ISDN-BRI with NT-1 Network Module
Sasa
>
> Dave
>
>
> Carmelo Garofalo
> <[EMAIL PROTECTED] To: [EMAIL PROTECTED]
> a.sas.com> cc:
> Sent by: Subject: Upgrade Cisco 2600
> [EMAIL PROTECTED]
> m
>
>
> 11/09/2000 11:14
> Please respond to
> Carmelo Garofalo
>
>
>
> Hi Guys,
> in my site there is a Cisco Router 2610 with the following hardware and
> software configuration:
>
> Cisco Internetwork Operating System Software
> IOS (tm) C2600 Software (C2600-D-M), Version 12.0(5)T1, RELEASE SOFTWARE
> (fc1)
> Copyright (c) 1986-1999 by cisco Systems, Inc.
> Compiled Tue 17-Aug-99 13:11 by cmong
>
> ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
>
> roma uptime is 2 weeks, 5 days, 22 hours, 47 minutes
> System returned to ROM by power-on at 10:44:34 UTC Fri Jan 7 2000
> System image file is "flash:c2600-d-mz.120-5.T1"
>
> cisco 2610 (MPC860) processor (revision 0x203) with 20480K/4096K bytes of
> memory
> .
> Processor board ...................
> M860 processor: part number 0, mask 49
> Bridging software.
> X.25 software, Version 3.0.0.
> Basic Rate ISDN software, Version 1.1.
> 1 Ethernet/IEEE 802.3 interface(s)
> 2 Serial(sync/async) network interface(s)
> 2 Low-speed serial(sync/async) network interface(s)
> 4 ISDN Basic Rate interface(s)
> 32K bytes of non-volatile configuration memory.
> 8192K bytes of processor board System flash (Read/Write)
>
> Configuration register is 0x2102
>
> The WIC ( 2 Serial Sync/Async) are busy for two sites, i must do a new
> site
> with a link at 2 Mbit. The configuration hardware ( 2 Low speed serial), of
> course, don't support the new link.
>
> With this architecture Can I repalce the WIC Low Speed Serial with the
> other WIC Serial (Sync/Async) at 2 Mbit?
>
> Regards,
>
> Carmelo
>
> Carmelo Garofalo
> System Support
> SAS Italy
> +39 (06) 32816650
> E-mail: [EMAIL PROTECTED]
>
> SAS ... The Power to Know
>
> _________________________________
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
> _________________________________
> FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
