=?utf-7?Q?FW=3A_CiscoWorks_+ACY-_HP_Openview_in_multiple_VLAN=2E?=

[=?utf-7?q?Ryan_Ngai_Hon_Kong?=]

Useful info.

Thanks Osama.

-----Original Message-----
From: Osama Kamal +AFs-mailto:OKamal+AEA-Mobinil.com+AF0-
Sent: Monday, January 08, 2001 4:55 PM
To: Ryan Ngai Hon Kong
Subject: RE: CiscoWorks +ACY- HP Openview in multiple VLAN.


I do not have NT here, but you should look in your manuals or in help files
for 1-using a seed file , 2-Redoing initial discovery.
NT and Unix are using the same configuration file names and parameters, the
difference will be only in the place of these files.


Osama

-----Original Message-----
From: Ryan Ngai Hon Kong +AFs-mailto:hkngai+AEA-jos.com.my+AF0-
Sent: Monday, January 08, 2001 10:54 AM
To: 'Osama Kamal'
Subject: RE: CiscoWorks +ACY- HP Openview in multiple VLAN.


Thanks for the feedback again.

What if I'm using the Openview for NT?
I think those command is not valid in NT.  :)
Thanks.

Ryan

-----Original Message-----
From: Osama Kamal +AFs-mailto:OKamal+AEA-Mobinil.com+AF0-
Sent: Monday, January 08, 2001 4:41 PM
To: Ryan Ngai Hon Kong
Subject: RE: CiscoWorks +ACY- HP Openview in multiple VLAN.


Ryan,
the seed file should contain all IP's of your all network devices. the seed
file should be stored in /etc/opt/OV/share/conf directory.
modify the netmon.lrf file to tell where the seed file is located
stop netmon with : ovstop netmon
edit netmon.lrf
add the following to the options area of the netmon.lrf file    -s
+ADw-pathname+AD4-/+ADw-file name+AD4-, the netmon.lrf should look like:
   OVs+AF8-YES+AF8-START:ovtopmd,pmd,ovwdb:-P -s
/etc/opt/OV/share/conf/seed+AF8-file:OVs+AF8-WELL+AF8-BEHAVED:15:PAUSE::

update the configuration with:
ovaddobj +ACQ-OV+AF8-LRF/netmon.lrf

redo initial discover
start netmon with    ovstart netmon

the seed file should NOT contain any blank lines
the seed file should contain only IP's




hope that will help

regards
Osama

-----Original Message-----
From: Ryan Ngai Hon Kong +AFs-mailto:hkngai+AEA-jos.com.my+AF0-
Sent: Monday, January 08, 2001 10:17 AM
To: 'Osama Kamal'
Subject: RE: CiscoWorks +ACY- HP Openview in multiple VLAN.


No Osama, I didn't use seed files.
Where do I go about this? I'm new to Open VIew...

Thanks for the time.
Ryan


-----Original Message-----
From: Osama Kamal +AFs-mailto:OKamal+AEA-Mobinil.com+AF0-
Sent: Monday, January 08, 2001 4:00 PM
To: Ryan Ngai Hon Kong
Subject: RE: CiscoWorks +ACY- HP Openview in multiple VLAN.


Do you use a seed file for OpenView? it not, then you should, if you need
more details, just send me.

Regards
Osama Kamal
Sr. Network Engineer
Egyptian Company for Mobile Services
(+-2012)3151298


-----Original Message-----
From: Ryan Ngai Hon Kong +AFs-mailto:hkngai+AEA-jos.com.my+AF0-
Sent: Monday, January 08, 2001 6:12 AM
To: 'cisco+AEA-groupstudy.com'
Subject: CiscoWorks +ACY- HP Openview in multiple VLAN.


Good day,

It seems that I'm stuck with a problem on my customer network. I doesn't
have much
idea about LANE and their existing network setup since it is managed by
other vendors
so the bottom line is that I cannot view their cisco router configuration at
all.
However base on their existing updated network schematic design, they have 4
core
catalyst switches with RSM module and few distribution +ACY- floor switches.

My current HP Openview and CiscoWorks configuration pointing the address of
the local 
catalyst RSM IP with SNMP read-only enabled. I'm expecting that the HP
Openview
to discover all the devices in the network while the CiscoWorks discover all
the routers
in the network by looking on the routing table in RSM.

At the end, it turns up that both of the network management software didn't
discover
any devices in the network even the after 2 days leaving it on my table to
discover.
Do you guys think that I should replicate/mirror all the other VLANs traffic
into my network
management port (SPAN)? 

Any idea or improvement should I look forward in case I left our any of
requirements?

Thanks in advance.

p/s: I'll be appreciate that if you intend to asked a question, please reply
to my email and I
will reply to your query to the group again to illuminate unnecessary
flooding.

Best wishes,
Ryan

+AF8AXwBfAF8AXwBfAF8AXwBfAF8AXwBfAF8AXwBfAF8AXwBfAF8AXwBfAF8AXwBfAF8AXwBfAF8AXwBfAF8AXwBf-
FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to abuse+AEA-groupstudy.com

_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]