I ran into exactly same problem. Check baud rate of your Hyper Terminal. I
think the default should be 9600. Try different rates and you will be able
to input command... Again, I ran into this couple weeks ago.
""Zahid Hassan"" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hi,
>
> I would really appreciate if someone could
> help me with the following problem :
>
> After powering up a 2500 router it goes through
> the boot process and hangs after a system restart.
>
> I can enter the ROM Monitor mode, but the console freezes
> and takes no command.
>
> Has anyone got any clue what this could be ?
>
>
> Cisco Internetwork Operating System Software
> IOS (tm) 2500 Software (C2500-IS-L), Version 12.0(8), RELEASE SOFTWARE
(fc1)
> Copyright (c) 1986-1999 by cisco Systems, Inc.
> Compiled Mon 29-Nov-99 13:51 by kpma
> Image text-base: 0x0303DE10, data-base: 0x00001000
>
> cisco 2500 (68030) processor (revision A) with 4096K/2048K bytes of
memory.
> Processor board ID 01497575, with hardware revision 00000000
> Bridging software.
> X.25 software, Version 3.0.0.
> Basic Rate ISDN software, Version 1.1.
> 1 Ethernet/IEEE 802.3 interface(s)
> 2 Serial network interface(s)
> 1 ISDN Basic Rate interface(s)
> 32K bytes of non-volatile configuration memory.
> 8192K bytes of processor board System flash (Read ONLY)
>
> Press RETURN to get started!
>
> 00:00:43: %LINK-3-UPDOWN: Interface BRI0, changed state to up
> 00:00:43: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
> 00:00:43: %LINK-3-UPDOWN: Interface Serial0, changed state to down
> 00:00:43: %LINK-3-UPDOWN: Interface Serial1, changed state to down
> 00:00:44: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0, changed
> state to down
> 00:00:44: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
changed
> state to down
> 00:00:44: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed
> state to down
> 00:00:44: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed
> state to down
> 00:00:46: %LINK-5-CHANGED: Interface Ethernet0, changed state to
> administratively down
> 00:00:47: %LINK-5-CHANGED: Interface BRI0, changed state to
administratively
> down
> 00:00:48: %LINK-5-CHANGED: Interface Serial0, changed state to
> administratively down
> 00:00:48: %SYS-5-CONFIG_I: Configured from memory by console
> 00:00:48: %SYS-5-RESTART: System restarted --
> Cisco Internetwork Operating System Software
> IOS (tm) 2500 Software (C2500-IS-L), Version 12.0(8), RELEASE SOFTWARE
(fc1)
> Copyright (c) 1986-1999 by cisco Systems, Inc.
> Compiled Mon 29-Nov-99 13:51 by kpma
> 00:00:49: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1, changed
> state to down
> 00:00:49: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:2, changed
> state to down
> 00:00:49: %LINK-5-CHANGED: Interface Serial1, changed state to
> administratively down
>
> _________________________________
> FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
