It looks like you have the switch set up as the DHCP server itself (not a
Microsoft DHCP server or other PC?) which appears to be in vlan 4 with the
following command:
!
ip dhcp-server 10.4.12.5
!
If it's not setup on the server I would remove that command above and see
what happens.. that's probably the problem.
Jeff
""Vijay Ramcharan"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hello Group,
> I'm looking at a particularly irritating problem and I can't quite figure
> out what's wrong. We have 2 Cat6509s which are suppposed to be configured
> for IP telephony. I've added a number of VLANs, implemented HSRP on the
> MSFCs etc. My problem is, I have a DHCP server on VLAN 4 which cannot be
> seen by a host which is on another VLAN. I tried using the ip
> helper-address command but was unsuccessful.
>
> Any ideas?
> Thanks.
>
> Configs below:
>
> Core_Even_MSFC#sh run
> Building configuration...
>
> Current configuration:
> !
> version 12.1
> no service pad
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname Core_Even_MSFC
> !
> boot system flash bootflash:c6msfc-jsv-mz.121-2.E.bin
> boot bootldr bootflash:c6msfc-boot-mz.121-2.E.bin
> !
> ip subnet-zero
> !
> mls rp ip
> cns event-service server
> !
> !
> !
> interface Serial9/0/0
> no ip address
> shutdown
> no fair-queue
> !
> interface Serial9/0/1
> no ip address
> shutdown
> no fair-queue
> !
> interface Serial9/0/2
> no ip address
> shutdown
> no fair-queue
> !
> interface Serial9/0/3
> no ip address
> shutdown
> no fair-queue
> !
> interface Vlan1
> ip address 10.4.10.2 255.255.254.0
> mls rp vtp-domain tdnyc
> mls rp management-interface
> !
> interface Vlan2
> ip address 10.4.8.2 255.255.254.0
> no ip redirects
> mls rp vtp-domain tdnyc
> standby 2 timers 5 15
> standby 2 priority 110 preempt
> standby 2 ip 10.4.8.5
> !
> interface Vlan3
> ip address 10.4.2.2 255.255.255.0
> no ip redirects
> mls rp vtp-domain tdnyc
> standby 3 timers 5 15
> standby 3 priority 100 preempt
> standby 3 ip 10.4.2.5
> !
> interface Vlan4
> ip address 10.4.12.2 255.255.254.0
> no ip redirects
> mls rp vtp-domain tdnyc
> standby 4 timers 5 15
> standby 4 priority 110 preempt
> standby 4 ip 10.4.12.4
> !
> interface Vlan5
> ip address 10.4.3.2 255.255.255.0
> no ip redirects
> mls rp vtp-domain tdnyc
> standby 5 timers 5 15
> standby 5 priority 100 preempt
> standby 5 ip 10.4.3.5
> !
> interface Vlan6
> ip address 10.4.14.2 255.255.255.0
> no ip redirects
> mls rp vtp-domain tdnyc
> standby 6 timers 5 15
> standby 6 priority 110 preempt
> standby 6 ip 10.4.14.5
> !
> interface Vlan7
> ip address 10.4.4.2 255.255.255.0
> no ip redirects
> mls rp vtp-domain tdnyc
> standby 7 timers 5 15
> standby 7 priority 100 preempt
> standby 7 ip 10.4.4.5
> !
> interface Vlan8
> ip address 10.4.15.2 255.255.255.0
> no ip redirects
> mls rp vtp-domain tdnyc
> standby 8 timers 5 15
> standby 8 priority 110 preempt
> standby 8 ip 10.4.15.5
> !
> interface Vlan9
> ip address 10.4.5.2 255.255.255.0
> no ip redirects
> mls rp vtp-domain tdnyc
> standby 9 timers 5 15
> standby 9 priority 100 preempt
> standby 9 ip 10.4.5.5
> !
> interface Vlan11
> ip address 10.4.6.2 255.255.255.0
> no ip redirects
> mls rp vtp-domain tdnyc
> standby 11 timers 5 15
> standby 11 priority 100 preempt
> standby 11 ip 10.4.6.5
> !
> interface Vlan15
> ip address 10.4.7.2 255.255.255.0
> no ip redirects
> mls rp vtp-domain tdnyc
> standby 15 timers 5 15
> standby 15 priority 100 preempt
> standby 15 ip 10.4.7.5
> !
> router eigrp 10
> network 10.0.0.0
> no auto-summary
> !
> ip classless
> no ip http server
> !
> !
> !
> line con 0
> transport input none
> line vty 0 4
> login
> transport input lat pad mop telnet rlogin udptn nasi
> !
> end
>
> Core_Even_MSFC#
>
> Core_Even (enable) sh conf
> This command shows non-default configurations only.
> Use 'show config all' to show both default and non-default configurations.
> ..................
> ..................
>
>
> ....................
>
>
>
> ...............
>
>
>
> ..
>
> begin
> !
> # ***** NON-DEFAULT CONFIGURATION *****
> !
> !
> #time: Thu Apr 12 2001, 15:44:31
> !
> #version 6.1(2)
> !
> set prompt Core_Even
> !
> #errordetection
> set errordetection portcounter enable
> !
> #!
> #vtp
> set vtp domain tdnyc
> set vlan 1 name default type ethernet mtu 1500 said 100001 state active
> set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state
active
> set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state
> activ
> e stp ieee
> set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state
> active st
> p ibm
> set vlan 2-9,11,15
> set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003
state
> acti
> ve mode srb aremaxhop 7 stemaxhop 7 backupcrf off
> !
> #ip
> set interface sc0 1 10.4.10.4/255.255.254.0 10.4.11.255
>
> set ip route 10.4.2.0/255.255.255.0 10.4.10.2
> set ip route 10.4.3.0/255.255.255.0 10.4.10.2
> set ip route 10.4.4.0/255.255.255.0 10.4.10.2
> set ip route 10.4.5.0/255.255.255.0 10.4.10.2
> set ip route 10.4.6.0/255.255.255.0 10.4.10.2
> set ip route 10.4.7.0/255.255.255.0 10.4.10.2
> set ip route 10.4.8.0/255.255.254.0 10.4.10.2
> set ip route 10.4.12.0/255.255.254.0 10.4.10.2
> set ip route 10.4.14.0/255.255.255.0 10.4.10.2
> set ip route 10.4.15.0/255.255.255.0 10.4.10.2
> set ip route 0.0.0.0/0.0.0.0 10.4.10.2
> !
> #spantree
> #vlan 1
> set spantree priority 16384 1
> #vlan 2
> set spantree priority 8192 2
> #vlan 3
> set spantree priority 16384 3
> #vlan 4
> set spantree priority 8192 4
> #vlan 5
> set spantree priority 16384 5
> #vlan 6
> set spantree priority 8192 6
> #vlan 7
> set spantree priority 16384 7
> #vlan 8
> set spantree priority 8192 8
> #vlan 9
> set spantree priority 16384 9
> #vlan 11
> set spantree priority 16384 11
> #vlan 15
> set spantree priority 16384 15
> !
> #set boot command
> set boot config-register 0x2
> set boot system flash bootflash:cat6000-sup.6-1-2.bin
> set boot system flash bootflash:cat6000-sup.5-5-5.bin
> set boot system flash bootflash:cat6000-sup.5-5-2.bin
> set boot system flash bootflash:cat6000-sup.5-3-4-CSX.bin
> !
> #qos
> set qos enable
> !
> #port channel
> set port channel 1/1-2 5
> !
> # default port status is enable
> !
> !
> #module 1 : 2-port 1000BaseX Supervisor
> !
> #module 2 empty
> !
> #module 3 : 8-port 1000BaseX Ethernet
> !
> #module 4 : 48-port 10/100BaseTX Ethernet
> set vlan 2 4/23-24
> set vlan 4 4/40-48
> set port auxiliaryvlan 4/1 4
> set port auxiliaryvlan 4/2 4
> set port auxiliaryvlan 4/3 4
> set port auxiliaryvlan 4/4 4
> set port auxiliaryvlan 4/5 4
> set port auxiliaryvlan 4/6 4
> set port auxiliaryvlan 4/7 4
> set port auxiliaryvlan 4/8 4
> set port auxiliaryvlan 4/9 4
> set port auxiliaryvlan 4/10 4
> set port auxiliaryvlan 4/11 4
> set port auxiliaryvlan 4/12 4
> set port auxiliaryvlan 4/13 4
> set port auxiliaryvlan 4/14 4
> set port auxiliaryvlan 4/15 4
> set port auxiliaryvlan 4/16 4
> set port auxiliaryvlan 4/17 4
> set port auxiliaryvlan 4/18 4
> set port auxiliaryvlan 4/19 4
> set port auxiliaryvlan 4/20 4
> set port auxiliaryvlan 4/21 4
> set port auxiliaryvlan 4/22 4
> set port auxiliaryvlan 4/23 4
> set port auxiliaryvlan 4/24 4
> set port auxiliaryvlan 4/25 4
> set port auxiliaryvlan 4/26 4
> set port auxiliaryvlan 4/27 4
> set port auxiliaryvlan 4/28 4
> set port auxiliaryvlan 4/29 4
> set port auxiliaryvlan 4/30 4
> set port auxiliaryvlan 4/31 4
> set port auxiliaryvlan 4/32 4
> set port auxiliaryvlan 4/33 4
> set port auxiliaryvlan 4/34 4
> set port auxiliaryvlan 4/35 4
> set port auxiliaryvlan 4/36 4
> set port auxiliaryvlan 4/37 4
> set port auxiliaryvlan 4/38 4
> set port auxiliaryvlan 4/39 4
> set port auxiliaryvlan 4/40 4
> set port auxiliaryvlan 4/41 4
> set port auxiliaryvlan 4/42 4
> set port auxiliaryvlan 4/43 4
> set port auxiliaryvlan 4/44 4
> set port auxiliaryvlan 4/45 4
> set port auxiliaryvlan 4/46 4
> set port auxiliaryvlan 4/47 4
> set port auxiliaryvlan 4/48 4
> set trunk 4/1 on dot1q 1-1005,1025-4094
> set trunk 4/2 on dot1q 1-1005,1025-4094
> set trunk 4/3 on dot1q 1-1005,1025-4094
> set trunk 4/4 on dot1q 1-1005,1025-4094
> set trunk 4/5 on dot1q 1-1005,1025-4094
> set trunk 4/6 on dot1q 1-1005,1025-4094
> set trunk 4/7 on dot1q 1-1005,1025-4094
> set trunk 4/8 on dot1q 1-1005,1025-4094
> set trunk 4/9 on dot1q 1-1005,1025-4094
> set trunk 4/10 on dot1q 1-1005,1025-4094
> set trunk 4/11 on dot1q 1-1005,1025-4094
> set trunk 4/12 on dot1q 1-1005,1025-4094
> set trunk 4/13 on dot1q 1-1005,1025-4094
> set trunk 4/14 on dot1q 1-1005,1025-4094
> set trunk 4/15 on dot1q 1-1005,1025-4094
> set trunk 4/16 on dot1q 1-1005,1025-4094
> set trunk 4/17 on dot1q 1-1005,1025-4094
> set trunk 4/18 on dot1q 1-1005,1025-4094
> set trunk 4/19 on dot1q 1-1005,1025-4094
> set trunk 4/20 on dot1q 1-1005,1025-4094
> set trunk 4/21 on dot1q 1-1005,1025-4094
> set trunk 4/22 on dot1q 1-1005,1025-4094
> set trunk 4/23 on dot1q 1-1005,1025-4094
> set trunk 4/24 on dot1q 1-1005,1025-4094
> set trunk 4/25 on dot1q 1-1005,1025-4094
> set trunk 4/26 on dot1q 1-1005,1025-4094
> set trunk 4/27 on dot1q 1-1005,1025-4094
> set trunk 4/28 on dot1q 1-1005,1025-4094
> set trunk 4/29 on dot1q 1-1005,1025-4094
> set trunk 4/30 on dot1q 1-1005,1025-4094
> set trunk 4/31 on dot1q 1-1005,1025-4094
> set trunk 4/32 on dot1q 1-1005,1025-4094
> set trunk 4/33 on dot1q 1-1005,1025-4094
> set trunk 4/34 on dot1q 1-1005,1025-4094
> set trunk 4/35 on dot1q 1-1005,1025-4094
> set trunk 4/36 on dot1q 1-1005,1025-4094
> set trunk 4/37 on dot1q 1-1005,1025-4094
> set trunk 4/38 on dot1q 1-1005,1025-4094
> set trunk 4/39 on dot1q 1-1005,1025-4094
> set trunk 4/40 on dot1q 1-1005,1025-4094
> set trunk 4/41 on dot1q 1-1005,1025-4094
> set trunk 4/42 on dot1q 1-1005,1025-4094
> set trunk 4/43 on dot1q 1-1005,1025-4094
> set trunk 4/44 on dot1q 1-1005,1025-4094
> set trunk 4/45 on dot1q 1-1005,1025-4094
> set trunk 4/46 on dot1q 1-1005,1025-4094
> set trunk 4/47 on dot1q 1-1005,1025-4094
> set trunk 4/48 on dot1q 1-1005,1025-4094
> !
> #module 5 empty
> !
> #module 6 empty
> !
> #module 7 empty
> !
> #module 8 : 8-port T1
> set port voice interface 8/1 dhcp enable vlan 4
> set port voice interface 8/2 dhcp enable vlan 4
> set port voice interface 8/3 dhcp enable vlan 4
> set port voice interface 8/4 dhcp enable vlan 4
> set port voice interface 8/5 dhcp enable vlan 4
> set port voice interface 8/6 dhcp enable vlan 4
> set port voice interface 8/7 dhcp enable vlan 4
> set port voice interface 8/8 dhcp enable vlan 4
> !
> #module 9 : 0-port FlexWAN Module
> !
> #module 15 : 1-port Multilayer Switch Feature Card
> !
> #module 16 empty
> end
> Core_Even (enable)
>
>
> Vijay Ramcharan
> FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=448&t=408
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
