For those not familiar with the original problem. Supervisor 1 and 2 models are most likely to have EARLs in this range - Sup IIIs typically have EARL 2 with NFFC-2. Check your system - and seriously consider the upgrade of CatOS. 'Be careful out there!' Cisco Security Advisory: Catalyst 5000 Series 802.1x Vulnerability ============================================================================ = Revision 1.0 For Public Release 2001 April 16 at 1500 UTC ------------------------------------------------------------------------ Summary ======= When an 802.1x frame is received by an affected Catalyst 5000 series switch on a STP blocked port it is forwarded in that VLAN instead of being dropped. This causes a performance impacting 802.1x frames network storm in that part of the network, which is made up of the affected Catalyst 5000 series switches. This network storm only subsides when the source of the 802.1x frames is removed or one of the workarounds in the workaround section is applied. This vulnerability can be exploited to produce a denial of service (DoS) attack. This vulnerability is described in Cisco bug id CSCdt62732. This notice will be posted at http://www.cisco.com/warp/public/707/cat5k-8021x-vuln-pub.shtml Affected Products ================= Cisco Catalyst 5000 series switches based on any of the following EARL (Encoded Address Recognition Logic) hardware revisions: * EARL 1 * EARL 1+ * EARL 1++ and running any of the following switch software revisions: * 4.5 (11) or earlier * 5.5 (6) or earlier * 6.1 (2) or earlier are affected by this vulnerability. This series includes the Catalyst models 5000, 5002, 5500, 5505, 5509, 2901, 2902 and 2926 switches. To determine your hardware and software revision type sh mod on the console prompt of the switch. Products Not Affected ===================== Catalyst 5000 series switches based on EARL 2 or later hardware revisions are not affected by this vulnerability. Catalyst 5000 series switches regardless of the EARL hardware revision, running the following switch software revisions * 4.5 (12) or later - expected general availability before 2001, May 1 * 5.5 (7) or later * 6.1 (3) or later are not affected by this vulnerability. No other Cisco product is currently known to be affected by this vulnerability. This includes the Catalyst 6000, 4000, 3500XL, 2900XL and 2948G switches. Details ======= When an 802.1x (IEEE standard for port based network access control) frame is received by an affected Catalyst 5000 series switch on a STP (Spanning Tree Protocol) blocked port it is forwarded in that VLAN (Virtual Local Area Network) instead of being dropped. This causes a performance impacting 802.1x frames network storm in that part of the network, which is made up of the affected Catalyst 5000 series switches. This network storm only subsides when the source of the 802.1x frames is removed or one of the workarounds in the workaround section is applied. The vulnerability is documented as Cisco bug id CSCdt62732. Impact ====== When an affected Catalyst 5000 series switch network receives an 802.1x frame it causes an 802.1x frames network storm. This network storm degrades the performance of the network. Slower ports on the affected Catalyst 5000 series switches may stop passing user data. The affected Catalyst 5000 series switches may not respond to any management inquiries via SNMP, Telnet or HTTP. However, management via the console port on the switches is still possible and can be used to apply the workarounds. Software Versions and Fixes =========================== This vulnerability has been fixed in the following switch software revisions * 4.5 (12) or later - expected availability before 2001, May 1 * 5.5 (7) or later * 6.1 (3) or later and the fix will be carried forward in all future releases. Software upgrade can be performed via the console interface. Obtaining Fixed Software ======================== Cisco is offering free software upgrades to remedy this vulnerability for all affected customers. Customers with service contracts may upgrade to any software release. Customers may install only the feature sets they have purchased. Fixed software is currently available except where noted. Customers with contracts should obtain upgraded software through their regular update channels. For most customers, this means that upgrades should be obtained via Cisco's Software Center at http://www.cisco.com/. Customers without contracts or warranty should get their upgrades by contacting the Cisco Technical Assistance Center (TAC) as shown below: * (800) 553-2447 (toll-free in North America) * +1 408 526 7209 (toll call from anywhere in the world) * e-mail: [EMAIL PROTECTED] See http://www.cisco.com/warp/public/687/Directory.shtml for additional TAC contact information, including instructions and e-mail addresses for use in various languages. Give the URL of this notice as evidence of your entitlement to a free upgrade. Free upgrades for non-contract customers must be requested through the TAC. Please do not contact either "[EMAIL PROTECTED]" or "[EMAIL PROTECTED]" for software upgrades; faster results will be obtained by contacting the TAC directly. Workarounds =========== The following workarounds will prevent the 802.1x frames from causing an 802.1x frames network storm in an affected Catalyst 5000 series switch network. These workarounds can also be applied to a network experiencing an 802.1x frames network storm. 1. Configure permanent MAC address entries for the entire reserved STP range 01-80-c2-00-00-02 to 01-80-c2-00-00-0f to be directed out an unused port for each VLAN on each affected switch in the network. The commands to configure are given below. set cam permanent 01-80-c2-00-00-02 / set cam permanent 01-80-c2-00-00-03 / set cam permanent 01-80-c2-00-00-04 / set cam permanent 01-80-c2-00-00-05 / set cam permanent 01-80-c2-00-00-06 / set cam permanent 01-80-c2-00-00-07 / set cam permanent 01-80-c2-00-00-08 / set cam permanent 01-80-c2-00-00-09 / set cam permanent 01-80-c2-00-00-0a / set cam permanent 01-80-c2-00-00-0b / set cam permanent 01-80-c2-00-00-0c / set cam permanent 01-80-c2-00-00-0d / set cam permanent 01-80-c2-00-00-0e / set cam permanent 01-80-c2-00-00-0f / 2. Break the STP loop by either a) Disabling the redundant (STP blocked ports) or b) Disconnecting the cable from these ports Remove all the sources of 802.1x frames before re-enabling the ports or reconnecting the cables. 3. Power down the Catalyst 5000 switch(es) that create the spanning-tree loop (any switch with STP blocked ports). Remove all the sources of 802.1x frames before powering up the switches. Exploitation and Public Announcements ===================================== The Cisco PSIRT is not aware of any malicious use of the vulnerability described in this advisory. A customer who discovered this vulnerability while using Microsoft Windows XP BETA software reported this vulnerability to Cisco. Microsoft Windows XP attempts 802.1x authentication during its boot-up phase. Following these configuration steps for Microsoft Windows XP can disable this: 1. Click on the associated Local Area Connection under Network Connections 2. Click on the Authentication Tab at the top right. 3. Uncheck "Network Access Control using IEEE 802.1x" This issue has been discussed in news articles regarding issues with Microsoft Windows XP BETA program and the Cisco Catalyst 5000 series switches. Status of This Notice: FINAL ============================ This is a FINAL notice. Although Cisco cannot guarantee the accuracy of all statements in this notice, all of the facts have been checked to the best of our ability. Cisco does not anticipate issuing updated versions of this notice unless there is some material change in the facts. Should there be a significant change in the facts, Cisco may update this notice. Distribution ============ This notice will be posted on Cisco's Worldwide Web site at http://www.cisco.com/warp/public/707/cat5k-8021x-vuln-pub.shtml FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
