Hi, Thanks for your info, I am using hme. But I have some futher question 1)From below, I know the way to set the duplex and speed, But how about the way to show the current speed and duplex type? I check my /etc/system file, there is no information regarding hme. Beside when I type ndd /dev/hme , it prompt me as below, what is name to get/set? refer to what ? tyogw01# ndd /dev/hme name to get/set ? 2)If I have different NIC in one solaris box, how to set it individually? Your command is "ndd /dev/hme -set adv_100fdx_cap=1" but it never specify which interface does it refer to ?? -----Original Message----- From: Thomas Crowe [mailto:[EMAIL PROTECTED]] Sent: Wednesday, May 16, 2001 10:21 AM To: Sim, CT (Chee Tong); [EMAIL PROTECTED] Subject: RE: How to know the duplex and speed setting of Solaris NIC?? [7:4626] That setting can be done 2 different ways (which both end up doing the same thing) On demand you can issue a 'ndd' command against the NIC driver (i.e. /dev/hme or /dev/qfe) like so: ndd /dev/qfe -set adv_autoneg_cap=0 ndd /dev/qfe -set adv_100fdx_cap=1 ndd /dev/qfe -set adv_100hdx_cap=1 ndd /dev/qfe -set adv_10fdx_cap=1 ndd /dev/qfe -set adv_10hdx_cap=1 The first ndd command turns off autonegotiation, this is needed Then you would enter ONE of the following commands to set the hard coded settings (100Full-Duplex, 100Half-duplex etc....) This helps for the immediate but not on subsequent reboots, to fix that you need to a set of similar lines to your /etc/system file like so: set qfe:qfe_adv_autoneg_cap = 0 set qfe:qfe_adv_100fdx_cap = 1 set qfe:qfe_adv_100hdx_cap = 0 set qfe:qfe_adv_10fdx_cap = 0 set qfe:qfe_adv_10hdx_cap = 0 I always put all of these entries in my /etc/system. Doing the HME interfaces are very similar, just replace the qfe with hme. Also note this changes ALL instances of the driver type (i.e. all 4 ports on a qfe, or every hme interface in a box) Hope this help. ______________________________ Thomas Crowe Technical Director Research & Development CTS - Atlanta Phone: 770-664-3900 ext 45 ______________________________ -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] Sent: Tuesday, May 15, 2001 9:22 PM To: [EMAIL PROTECTED] Subject: How to know the duplex and speed setting of Solaris NIC?? [7:4626] Hi.. How to know the duplex and speed setting of Solaris NIC?? Many thanks Tong ================================================================== De informatie opgenomen in dit bericht kan vertrouwelijk zijn en is uitsluitend bestemd voor de geadresseerde. Indien u dit bericht onterecht ontvangt wordt u verzocht de inhoud niet te gebruiken en de afzender direct te informeren door het bericht te retourneren. ================================================================== The information contained in this message may be confidential and is intended to be exclusively for the addressee. Should you receive this message unintentionally, please do not use the contents herein and notify the sender immediately by return e-mail. ================================================================== FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] This message was sent with an attachment which Rabobank International does not allow because the filetype is not considered to be business related or it contains "executable" code which could be destructive if run. Please note the attachment has now been deleted. Should the attachment contain business critical information then the sender should use an alternative file format to deliver the information. The original header content is included below The following files were deleted: Thomas Crowe.vcf ================================================================== ================================================================== De informatie opgenomen in dit bericht kan vertrouwelijk zijn en is uitsluitend bestemd voor de geadresseerde. Indien u dit bericht onterecht ontvangt wordt u verzocht de inhoud niet te gebruiken en de afzender direct te informeren door het bericht te retourneren. ================================================================== The information contained in this message may be confidential and is intended to be exclusively for the addressee. Should you receive this message unintentionally, please do not use the contents herein and notify the sender immediately by return e-mail. ================================================================== Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=4642&t=4642 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
