We're running two threads on the same subject. You should have been reading
the other thread. Anyway - do a clear line 1, clear line 2. That will free
up your lines. The "*" in front of a line means that the router thinks that
it is in use. Then from your prompt enter "r1" it should then say something
like "trying ..." Hit enter. That should get you to your target router. I
assume that you can connect to the target router with a regular console
cable from a PC. You do have the first octal cable connected to the first
router.
> -----Original Message-----
> From: Jeongwoo Park [mailto:[EMAIL PROTECTED]]
> Sent: Saturday, May 19, 2001 9:34 AM
> To: [EMAIL PROTECTED]
> Subject: Terminal Server for the first time !!! [7:5119]
>
>
> Hi all
> How can I get my 2509 terminal server to work?
> Here is my config
>
> TermServer#sh r
> 05:47:29: %SYS-5-CONFIG_I: Configured from console by consoleun
> Building configuration...
>
> Current configuration:
> !
> version 12.0
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname TermServer
> !
> enable password wams
> !
> ip subnet-zero
> no ip domain-lookup
> ip host r1 2001 1.1.1.1
> ip host r2 2002 1.1.1.1
> ip host r3 2003 1.1.1.1
> !
> !
> !
> interface Loopback0
> ip address 1.1.1.1 255.255.255.255
> no ip directed-broadcast
> !
> interface Ethernet0
> no ip address
> no ip directed-broadcast
> shutdown
> !
> interface Serial0
> ip address 2.2.50.2 255.255.255.252
> no ip directed-broadcast
> no ip mroute-cache
> no fair-queue
> clockrate 64000
> shutdown
>
> !
> interface Serial1
> ip address 3.3.50.1 255.255.255.252
> no ip directed-broadcast
> clockrate 1300000
> shutdown
> !
> ip classless
> !
> !
> line con 0
> line 1 8
> no exec
> transport input all
> line aux 0
> line vty 0 4
> login
> !
> end
>
> I have three other router that are r1, r2, and r3 respectively.
> How can I get to r1, r2, or r3?
> Isn't it this one? for example,
> TermServer#r1
> TermServer#r2
> TermServer#r3
> It did not work
> I am using termserver for the first time.
> Can someone guide me through how to use it?
>
> In addition, here is output of "sh line"
>
> TermServer#sh line
> Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise
> Overruns Int
> * 0 CTY - - - - - 6 1
> 0/0 -
> * 1 TTY 9600/9600 - - - - - 3 2
> 0/0 -
> * 2 TTY 9600/9600 - - - - - 2 0
> 0/0 -
> 3 TTY 9600/9600 - - - - - 1 0
> 0/0 -
> 4 TTY 9600/9600 - - - - - 0 0
> 0/0 -
> 5 TTY 9600/9600 - - - - - 0 104
> 0/0 -
> 6 TTY 9600/9600 - - - - - 0 0
> 0/0 -
> 7 TTY 9600/9600 - - - - - 1 0
> 81/243 -
> 8 TTY 9600/9600 - - - - - 0 6
> 208/622 -
> 9 AUX 9600/9600 - - - - - 0 0
> 0/0 -
> 10 VTY - - - - - 1 0
> 0/0 -
> 11 VTY - - - - - 0 0
> 0/0 -
> 12 VTY - - - - - 0 0
> 0/0 -
> 13 VTY - - - - - 0 0
> 0/0 -
> 14 VTY - - - - - 0 0
> 0/0 -
> Thanks
>
> jp
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct
> and Nondisclosure violations to [EMAIL PROTECTED]
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=5205&t=5119
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
