Add a "atm clock internal" to each interface.
I'm not familiar with your encapsulation method. If the above doesn't work
try changing to aal5snap.
You will not be able to ping your local interface unless you also create a
map statement for it. When you have this up and running then try doing
subinterfaces. You could have one large map-list or you could create a
map-list for each subinterface. More typing but much easier to troubleshoot
several months later.
> -----Original Message-----
> From: Deloso, Elmer G (WPNSTA Yorktown)
> [mailto:[EMAIL PROTECTED]]
> Sent: Friday, May 25, 2001 9:21 AM
> To: [EMAIL PROTECTED]
> Subject: ATM int are up, unable to ping. [7:5901]
>
>
> Hi, everyone.
> I've just installed a single-mode ATM module on each of my
> 4500's, both
> routers recognize the card. I configure them as shown below,
> however I can't
> ping even the local ATM interface even though it shows as
> being up. I also
> icluded the debug output. Please tell me what's not right. Thanks in
> advance.
> Elmer Deloso
>
> RouterA#ping 195.1.1.1
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 195.1.1.1, timeout is 2 seconds:
> .....
> Success rate is 0 percent (0/5)
> RouterA#ping 195.1.1.2
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 195.1.1.2, timeout is 2 seconds:
> .....
> Success rate is 0 percent (0/5)
> RouterA#sh run
> Building configuration...
> Current configuration:
> !
> version 11.3
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname RouterA
> !
> !
> !
> !
> interface Ethernet0
> no ip address
> shutdown
> media-type 10BaseT
> !
> interface Ethernet1
> no ip address
> shutdown
> media-type 10BaseT
> !
> interface Serial0
> no ip address
> no ip mroute-cache
> shutdown
> no fair-queue
> !
> interface Serial1
> no ip address
> shutdown
> !
> interface ATM0
> ip address 195.1.1.2 255.255.255.0
> atm max-paks-vc 40
> atm pvc 1 0 32 aal5nlpid
> map-group 1
> !
> no ip classless
> !
> !
> map-list 1
> ip 195.1.1.1 atm-vc 1 broadcast
> !
> line con 0
> line aux 0
> line vty 0 4
> login
> !
> end
> RouterA#sh ver
> Cisco Internetwork Operating System Software
> IOS (tm) 4500 Software (C4500-IS-M), Version 11.3(11b),
> RELEASE SOFTWARE
> (fc1)
> Copyright (c) 1986-2001 by cisco Systems, Inc.
> Compiled Fri 02-Mar-01 14:28 by cmong
> Image text-base: 0x60008930, data-base: 0x60780000
> ROM: System Bootstrap, Version 5.3(16) [richardd 16], RELEASE
> SOFTWARE (fc1)
>
> BOOTFLASH: 4500 Software (C4500-BOOT-M), Version 11.1(7),
> RELEASE SOFTWARE
> (fc2)
> RouterA uptime is 6 minutes
> System restarted by reload
> System image file is "flash:c4500-is-mz.113-11b.bin", booted
> via flash
> cisco 4500 (R4K) processor (revision B) with 16384K/4096K
> bytes of memory.
> Processor board ID 03454024
> R4700 processor, Implementation 33, Revision 1.0
> G.703/E1 software, Version 1.0.
> Bridging software.
> X.25 software, Version 3.0.0.
> 2 Ethernet/IEEE 802.3 interface(s)
> 2 Serial network interface(s)
> 1 ATM network interface(s)
> 128K bytes of non-volatile configuration memory.
> 4096K bytes of processor board System flash (Read/Write)
> 4096K bytes of processor board Boot flash (Read/Write)
> Configuration register is 0x2102
> RouterA#sh int atm0
> ATM0 is up, line protocol is up
> Hardware is ATMizer BX-50
> Internet address is 195.1.1.2/24
> MTU 4470 bytes, sub MTU 4470, BW 155520 Kbit, DLY 100 usec,
> reliability 13/255, txload 1/255, rxload 1/255
> Encapsulation ATM, loopback not set, keepalive not supported
> Encapsulation(s): AAL5 AAL3/4, PVC mode
> 1024 maximum active VCs, 1024 VCs per VP, 1 current VCCs
> VC idle disconnect time: 300 seconds
> Last input never, output 00:01:04, output hang never
> Last clearing of "show interface" counters never
> Queueing strategy: fifo
> Output queue 0/40, 0 drops; input queue 0/75, 0 drops
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 0 packets input, 0 bytes, 0 no buffer
> Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
> 3 input errors, 3 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
> 5 packets output, 530 bytes, 0 underruns
> 0 output errors, 0 collisions, 1 interface resets
> 0 output buffer failures, 0 output buffers swapped out
> RouterA#sh atm vc
> AAL / Peak Avg. Burst
> Interface VCD VPI VCI Type Encapsulation Kbps Kbps Cells
> Status
> 0 1 0 32 PVC AAL5-NLPID 155000 155000 95 ACT
> RouterB#sh run
> Building configuration...
> Current configuration:
> !
> version 11.3
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname RouterB
> !
> !
> !
> !
> interface Ethernet0
> no ip address
> shutdown
> media-type 10BaseT
> !
> interface Ethernet1
> no ip address
> shutdown
> media-type 10BaseT
> !
> interface Serial0
> no ip address
> no ip mroute-cache
> shutdown
> no fair-queue
> !
> interface Serial1
> no ip address
> shutdown
> !
> interface Serial2
> no ip address
> shutdown
> !
> interface Serial3
> no ip address
> shutdown
> !
> interface ATM0
> ip address 195.1.1.1 255.255.255.0
> atm max-paks-vc 40
> atm pvc 1 0 32 aal5nlpid
> map-group 1
> !
> no ip classless
> !
> !
> map-list 1
> ip 195.1.1.2 atm-vc 1 broadcast
> !
> line con 0
> line aux 0
> line vty 0 4
> login
> !
> end
> RouterB#sh ver
> Cisco Internetwork Operating System Software
> IOS (tm) 4500 Software (C4500-IS-M), Version 11.3(11b),
> RELEASE SOFTWARE
> (fc1)
> Copyright (c) 1986-2001 by cisco Systems, Inc.
> Compiled Fri 02-Mar-01 14:28 by cmong
> Image text-base: 0x60008930, data-base: 0x60780000
> ROM: System Bootstrap, Version 5.2(7b) [mkamson 7b], RELEASE
> SOFTWARE (fc1)
> BOOTFLASH: 4500 Bootstrap Software (C4500-BOOT-M), Version
> 10.3(7), RELEASE
> SOFTWARE (fc1)
> RouterB uptime is 11 minutes
> System restarted by reload
> System image file is "flash:c4500-is-mz.113-11b.bin", booted
> via flash
> cisco 4500 (R4K) processor (revision B) with 16384K/4096K
> bytes of memory.
> Processor board ID 03421072
> R4700 processor, Implementation 33, Revision 1.0
> G.703/E1 software, Version 1.0.
> Bridging software.
> X.25 software, Version 3.0.0.
> 2 Ethernet/IEEE 802.3 interface(s)
> 4 Serial network interface(s)
> 1 ATM network interface(s)
> 128K bytes of non-volatile configuration memory.
> 4096K bytes of processor board System flash (Read/Write)
> 4096K bytes of processor board Boot flash (Read/Write)
> Configuration register is 0x2102
> RouterB#sh int atm0
> ATM0 is up, line protocol is up
> Hardware is ATMizer BX-50
> Internet address is 195.1.1.1/24
> MTU 4470 bytes, sub MTU 4470, BW 155520 Kbit, DLY 100 usec,
> reliability 0/255, txload 1/255, rxload 1/255
> Encapsulation ATM, loopback not set, keepalive not supported
> Encapsulation(s): AAL5 AAL3/4, PVC mode
> 1024 maximum active VCs, 1024 VCs per VP, 1 current VCCs
> VC idle disconnect time: 300 seconds
> Last input never, output never, output hang never
> Last clearing of "show interface" counters never
> Queueing strategy: fifo
> Output queue 0/40, 0 drops; input queue 0/75, 0 drops
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 0 packets input, 0 bytes, 0 no buffer
> Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
> 111 input errors, 111 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
> 0 packets output, 0 bytes, 0 underruns
> 0 output errors, 0 collisions, 1 interface resets
> 0 output buffer failures, 0 output buffers swapped out
> RouterB#sh atm vc
> AAL / Peak Avg. Burst
> Interface VCD VPI VCI Type Encapsulation Kbps Kbps Cells Status
> 0 1 0 32 PVC AAL5-NLPID 155000 155000 95 ACT
> RouterB#ping 195.1.1.1
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 195.1.1.1, timeout is 2 seconds:
> .
> 00:12:43: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> ATM0, changed
> state to down
> 00:12:44: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> ATM0, changed
> state to up....
> Success rate is 0 percent (0/5)
> RouterB#ping 195.1.1.2
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 195.1.1.2, timeout is 2 seconds:
> .....
> Success rate is 0 percent (0/5)
>
> Here's the debug output when I do a ping...
> RouterA#debug atm packet
> RouterA#ping 195.1.1.1
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 195.1.1.1, timeout is 2 seconds:
> 00:20:29: ATM0(O):
> VCD:0x1 DM:0x100 NLPID:0x03CC Length:0x6A
> 00:20:29: 4500 0064 0005 0000 FF01 338E C301 0102 C301 0101
> 0800 7C2A 2625
> 1974 0000
> 00:20:29: 0000 0012 C274 ABCD ABCD ABCD ABCD ABCD ABCD ABCD
> ABCD ABCD ABCD
> ABCD ABCD
> 00:20:29: ABCD ABCD ABCD ABCD ABCD ABCD ABCD ABCD ABCD ABCD
> ABCD ABCD ABCD
> ABCD ABCD
> 00:20:29: .
> 00:20:31: ATM0(O):
> VCD:0x1 DM:0x100 NLPID:0x03CC Length:0x6A
> 00:20:31: 4500 0064 0006 0000 FF01 338D C301 0102 C301 0101
> 0800 7459 2626
> 1974 0000
> 00:20:31: 0000 0012 CA44 ABCD ABCD ABCD ABCD ABCD ABCD ABCD
> ABCD ABCD ABCD
> ABCD ABCD
> 00:20:31: ABCD ABCD ABCD ABCD ABCD ABCD ABCD ABCD ABCD ABCD
> ABCD ABCD ABCD
> ABCD ABCD
> 00:20:31: .
> 00:20:33: ATM0(O):
> VCD:0x1 DM:0x100 NLPID:0x03CC Length:0x6A
> 00:20:33: 4500 0064 0007 0000 FF01 338C C301 0102 C301 0101
> 0800 6C88 2627
> 1974 0000
> 00:20:33: 0000 0012 D214 ABCD ABCD ABCD ABCD ABCD ABCD ABCD
> ABCD ABCD ABCD
> ABCD ABCD
> 00:20:33: ABCD ABCD ABCD ABCD ABCD ABCD ABCD ABCD ABCD ABCD
> ABCD ABCD ABCD
> ABCD ABCD
> 00:20:33: .
> 00:20:35: ATM0(O):
> VCD:0x1 DM:0x100 NLPID:0x03CC Length:0x6A
> 00:20:35: 4500 0064 0008 0000 FF01 338B C301 0102 C301 0101
> 0800 64B7 2628
> 1974 0000
> 00:20:35: 0000 0012 D9E4 ABCD ABCD ABCD ABCD ABCD ABCD ABCD
> ABCD ABCD ABCD
> ABCD ABCD
> 00:20:35: ABCD ABCD ABCD ABCD ABCD ABCD ABCD ABCD ABCD ABCD
> ABCD ABCD ABCD
> ABCD ABCD
> 00:20:35: .
> 00:20:37: ATM0(O):
> VCD:0x1 DM:0x100 NLPID:0x03CC Length:0x6A
> 00:20:37: 4500 0064 0009 0000 FF01 338A C301 0102 C301 0101
> 0800 5CE6 2629
> 1974 0000
> 00:20:37: 0000 0012 E1B4 ABCD ABCD ABCD ABCD ABCD ABCD ABCD
> ABCD ABCD ABCD
> ABCD ABCD
> 00:20:37: ABCD ABCD ABCD ABCD ABCD ABCD ABCD ABCD ABCD ABCD
> ABCD ABCD ABCD
> ABCD ABCD
> 00:20:37: .
> Success rate is 0 percent (0/5)
> RouterA#undebug atm packet
> I also notice that the atm link flaps like this...
> 00:15:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> ATM0, changed
> state to down
> 00:15:10: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> ATM0, changed
> state to up
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct
> and Nondisclosure violations to [EMAIL PROTECTED]
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=5907&t=5901
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
