The 3600 certainly does support the WIC-2T.
Dave
,
Makarand Yerawadekar wrote:
>
> Cisco 2600 series does not support NM-4T, incidentally Cisco 3600 series
> can not accept WIC-2
>
> At 11:17 AM 9/4/01 -0400, Daniel Cotts wrote:
> >I don't believe that the NM-4T= four port serial module will work in any
> >2600 series router. Folks here on the list have mentioned using two
WIC-2T=
> >with 2600s. Keep in mind that those modules require the SmartSerial
cables.
> >
> > > -----Original Message-----
> > > From: Ahmed Mamoor Amimi [mailto:[EMAIL PROTECTED]]
> > > Sent: Tuesday, September 04, 2001 12:47 AM
> > > To: [EMAIL PROTECTED]
> > > Subject: Re: Regarding cisco routers [7:18368]
> > >
> > >
> > > 2509 was of worth for the old CCIE lab where u need it....
> > > but now this
> > > router is been replaced with
> > > a KNOB SWITCH to get in to each router ... like the printer
> > > switch box used
> > > to swtich printer b/w PC.
> > > and for the CCNA/CCNP u really dont need to have it......
> > > this router is
> > > good but also expensive... why waste
> > > money on that u dont want in the lab, the only benefit left
> > > with this router
> > > is eight ASYNC ports used for DDR
> > > and stuff... but this u can do it from every router that have
> > > an AUX port as
> > > AUX is an ASYNC port too.
> > > I think u should have a router with have atleast 4 serial
> > > ports so u can
> > > make that router a frame-relay switch.
> > > and in my opinoin u should buy a 2620 with 4 port serial
> > > module... by this u
> > > can have that router act as a
> > > frame-relay switch as it will have 4 serial and also can be used for
> > > inter-vlan routing b/w ur switches....
> > > That will be a complete lab for CCIE level except token-ring
> > > switching and
> > > ATM.
> > >
> > > enjoy ....
> > > -Mamoor
> > > CCNP/CNE/MCT/MCSE/A+/NETWORK+/CCIE(writen)
> > >
> > >
> > > wrote in message
> > > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> > > > I am considering purchasing a 2509 router because I need to
> > > telnet into my
> > > > other four without beating up on my PC serial ports. I
> > > currently own 4
> > > > routers TWO 2501, ONE 2503, One 2514, also an isdn 804,
> > > catalyst 5000 and
> > > > 1900EN switch. I was told the 2509 would be a perfect
> > > addition since I
> > > > would
> > > > be able to log in utiilizing one console port on my PC to
> > > eight on the
> > > 2509
> > > > router. Are there any other good uses of the 2509 other
> > > then consoling
> > > > in...for instance....do I need to have it for my CCNA or
> > > CCNP?? also
> > > should
> > > > I drop any of the other routers or do you think I should
> > > keep them...again
> > > > these routers are for studying only.
> > > >
> > > > P.s. I forgot to mention I also have a isdn simulator...sorry for
> > > > boasting..but I do need expert advice here and don't want
> > > to burn money on
> > > > things I don't need.
> > > >
> > > > thank you
> > > Report misconduct
> > > and Nondisclosure violations to [EMAIL PROTECTED]
--
David Madland
Sr. Network Engineer
CCIE# 2016
Qwest Communications Int. Inc.
[EMAIL PROTECTED]
612-664-3367
"Emotion should reflect reason not guide it"
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=18619&t=18368
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
