in your config .... what is your LMI.....(autosence)
have you set the encapsulation command on the int`s see this link http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/wan_c/wcdfrely.htm#xtocid221854 input errors usually mean that there is some kind of encap error...(int doesn`t understand the packet/frame it`s recieving).... CU steve >From: "Symon Thurlow" >Reply-To: "Symon Thurlow" >To: [EMAIL PROTECTED] >Subject: Help with huge amount of Input/Frame and some CRC errors [7:21647] >Date: Tue, 2 Oct 2001 04:47:46 -0400 > >Hi All, > >I have a 2MB leased line (UK Megastream) line between two sites. > >One site has a 3640, the other a 2621. > >The line is presented as G703 both ends. > >I have PDA DC2020 G703 to X21 converters at both ends. > >so connection is: > >SITE A >Cisco 3640 (WIC-1T) >PDA DC2020 X21 to G703 Converter >Megastream box (CSU/DSU) >Carriers network >Megastream Box (CSU/DSU) >PDA DC2020 X21 to G703 Converter >Cisco 2621 (WIC-1T) > >When I do local and remote loopback tests, using extended pings, there >are no errors. This is true from both ends. > >As soon as I take the line off loopback, the activity light on the >2621 goes crazy, and I get about 500 input errors per second on one >end, and about 300 or so per second on the other end. > >Keepalives are incrementing, I have tried invert txclock, although >probably didn't need to. > >Here is a sh int from each end, ip addresses changed: > >2621 end: > > >sh int s0/0 >Serial0/0 is up, line protocol is up > Hardware is PowerQUICC Serial > Description: xxxxxxxxxxxxxxxx > Internet address is 10.10.10.2/30 > MTU 1500 bytes, BW 2048 Kbit, DLY 20000 usec, > reliability 157/255, txload 1/255, rxload 1/255 > Encapsulation HDLC, loopback not set > Keepalive set (10 sec) > Last input 00:00:08, output 00:00:00, output hang never > Last clearing of "show interface" counters 17:21:37 > Queueing strategy: fifo > Output queue 0/40, 0 drops; input queue 0/75, 0 drops > 5 minute input rate 0 bits/sec, 0 packets/sec > 5 minute output rate 0 bits/sec, 0 packets/sec > 7055 packets input, 433584 bytes, 0 no buffer > Received 7055 broadcasts, 0 runts, 0 giants, 0 throttles > 30613034 input errors, 4438685 CRC, 26174345 frame, 0 overrun, 0 >ignored, 4 > abort > 8850 packets output, 838333 bytes, 0 underruns > 0 output errors, 0 collisions, 3 interface resets > 0 output buffer failures, 0 output buffers swapped out > 0 carrier transitions > DCD=up DSR=up DTR=up RTS=up CTS=up > >3640 end: > > >sh int s0/0 >Serial0/0 is up, line protocol is up > Hardware is QUICC Serial > Description: xxxxxxxxxxxxxxxxxxxx > Internet address is 10.10.10.1/30 > MTU 1500 bytes, BW 2048 Kbit, DLY 20000 usec, rely 161/255, load >1/255 > Encapsulation HDLC, loopback not set, keepalive set (10 sec) > Last input 00:00:00, output 00:00:00, output hang never > Last clearing of "show interface" counters 17:22:15 > Queueing strategy: fifo > Output queue 0/40, 0 drops; input queue 0/75, 0 drops > 5 minute input rate 0 bits/sec, 1 packets/sec > 5 minute output rate 0 bits/sec, 1 packets/sec > 8485 packets input, 778380 bytes, 0 no buffer > Received 7961 broadcasts, 0 runts, 0 giants, 0 throttles > 18292244 input errors, 5169 CRC, 18287064 frame, 0 overrun, 0 >ignored, 11 a >bort > 7324 packets output, 462192 bytes, 0 underruns > 0 output errors, 0 collisions, 10 interface resets > 0 output buffer failures, 0 output buffers swapped out > 0 carrier transitions > DCD=up DSR=up DTR=up RTS=up CTS=up > >Carrier (NTL) say that line is fine. Remote loopback test sort of >point to this as being true (to my limited knowledge). > >Any assistance greatly appreciated. > >Cheers, > >Symon _________________________________________________________________ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=21649&t=21649 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]