Well it has a configuration builder but I hated it ;) The only use I had for it was resetting the internal IP address so I could telnet into it when I bought it (without the weird female-male serial cable for the console). ;)
And yes...SPIDS would be a problem in Japan..rofl. Allen ----- Original Message ----- From: anil To: Allen May ; Sent: Saturday, November 24, 2001 12:52 PM Subject: RE: Cisco 700 series in Remote Access exam (640-50 [7:26975] > It took me 6 weeks :-) > Honest! > I was in Japan and they sent me the US version of ISDN which set me back a > week or 2(No SPIDS in Japan). But it still took me a while. My CCIE collegue > was not able to help me, and that is how I found out about the "IOS" (or > lack of it). > -Anil > > > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Allen May > Sent: Saturday, November 24, 2001 4:10 PM > To: [EMAIL PROTECTED] > Subject: Re: Cisco 700 series in Remote Access exam (640-50 [7:26975] > > > I have a 776 and it's definitely NOT IOS. However the manuals are all still > available for free on cisco.com. It's very limited on commands so you could > learn it in a day just from looking at docs & config examples. I set mine > up in about 30 minutes with no experience in it whatsoever. > > Here is my config (slightly altered) with a copy of the commands available > with the help menu (?). > > amay128> upload > CD > SET SCREENLENGTH 20 > SET COUNTRYGROUP 1 > SET LAN MODE ANY > SET WAN MODE ONLY > SET AGE OFF > SET MULTIDESTINATION OFF > SET SWITCH NI-1 > SET 1 SPID 51255512120101 > SET 1 DIRECTORYNUMBER 5125551212 > SET PHONE1 = 5125551212 > SET 2 SPID 51255512120101 > SET 2 DIRECTORYNUMBER 5125551212 > SET PHONE2 = 5125551212 > SET AUTODETECTION OFF > SET CONFERENCE 60 > SET TRANSFER 61 > SET 1 DELAY 30 > SET 2 DELAY 30 > SET BRIDGING ON > SET LEARN ON > SET PASSTHRU OFF > SET SPEED 64K > SET PLAN NORMAL > SET D AUTO OFF > SET 1 AUTO ON > SET 2 AUTO ON > SET 1 NUMBER > SET 2 NUMBER > SET AODI OFF > SET 1 BACKUPNUMBER > SET 2 BACKUPNUMBER > SET 1 RINGBACK > SET 2 RINGBACK > SET 1 CLIVALIDATENUMBER > SET 2 CLIVALIDATENUMBER > SET CLICALLBACK OFF > SET CLIAUTHENTICATION OFF > SET SYSTEMNAME amay128 > LOG CALLS VERBOSE > LOG ERRORS VERBOSE > SET UNICASTFILTER OFF > DEMAND D THRESHOLD 0 > DEMAND 1 THRESHOLD 0 > DEMAND 2 THRESHOLD 60 > DEMAND D DURATION 1 > DEMAND 1 DURATION 1 > DEMAND 2 DURATION 4 > DEMAND D SOURCE LAN > DEMAND 1 SOURCE LAN > DEMAND 2 SOURCE BOTH > TIMEOUT D THRESHOLD 0 > TIMEOUT 1 THRESHOLD 0 > TIMEOUT 2 THRESHOLD 48 > TIMEOUT D DURATION 0 > TIMEOUT 1 DURATION 0 > TIMEOUT 2 DURATION 120 > TIMEOUT D SOURCE LAN > TIMEOUT 1 SOURCE LAN > TIMEOUT 2 SOURCE BOTH > SET PASSWORD SYSTEM ENCRYPTED *************** > SET REMOTEACCESS PROTECTED > SET LOCALACCESS ON > SET LOGOUT 60 > SET CALLERID ON > SET PPP AUTHENTICATION IN CHAP PAP > SET PPP CHAPREFUSE NONE > SET PPP CHAPALLOW MULTIHOST OFF > SET PPP MAGICNUMBERCHECK ON > SET PPP AUTHENTICATION OUT NONE > SET PPP AUTHENTICATION ACCEPT EITHER > SET PPP TAS CLIENT 0.0.0.0 > SET PPP TAS CHAPSECRET LOCAL ON > SET PPP PASSWORD CLIENT ENCRYPTED ************** > SET PPP SECRET CLIENT ENCRYPTED ******************* > SET PPP CALLBACK REQUEST OFF > SET PPP CALLBACK REPLY OFF > SET PPP NEGOTIATION INTEGRITY 10 > SET PPP NEGOTIATION COUNT 10 > SET PPP NEGOTIATION RETRY 3000 > SET PPP TERMREQ COUNT 2 > SET PPP MULTILINK ON > SET PPP MULTILINK PPPHEADER ON > SET COMPRESSION STAC > SET PPP BACP ON > SET PPP ADDRESS NEGOTIATION LOCAL OFF > SET PPP IP NETMASK LOCAL OFF > SET IP PAT UDPTIMEOUT 5 > SET IP PAT TCPTIMEOUT 30 > SET IP RIP TIME 30 > SET X25 LIC 0 > SET X25 HIC 0 > SET X25 LTC 0 > SET X25 HTC 0 > SET X25 LOC 1024 > SET X25 HOC 1024 > SET CALLDURATION 0 > SET SNMP CONTACT "Allen May" > SET SNMP LOCATION "AMay128 - Home" > SET SNMP TRAP COLDSTART OFF > SET SNMP TRAP WARMSTART OFF > SET SNMP TRAP LINKDOWN OFF > SET SNMP TRAP LINKUP OFF > SET SNMP TRAP AUTHENTICATIONFAIL OFF > SET DHCP OFF > SET DHCP DOMAIN > SET DHCP NETBIOS_SCOPE > SET TPAD PARITY NONE > SET X25D TEI 0 > SET X25D X121HOST > SET VOICEPRIORITY INCOMING INTERFACE PHONE1 CONDITIONAL > SET VOICEPRIORITY OUTGOING INTERFACE PHONE1 CONDITIONAL > SET CALLWAITING INTERFACE PHONE1 ON > SET VOICEPRIORITY INCOMING INTERFACE PHONE2 ALWAYS > SET VOICEPRIORITY OUTGOING INTERFACE PHONE2 ALWAYS > SET CALLWAITING INTERFACE PHONE2 ON > SET CALLTIME VOICE INCOMING OFF > SET CALLTIME VOICE OUTGOING OFF > SET CALLTIME DATA INCOMING OFF > SET CALLTIME DATA OUTGOING OFF > SET USER LAN > SET IP ROUTING ON > SET IP ADDRESS 207.x.y.z > SET IP NETMASK 255.255.255.248 > SET IP FRAMING ETHERNET_II > SET IP PROPAGATE ON > SET IP COST 1 > SET IP RIP RECEIVE BO > SET IP RIP UPDATE OFF > SET IP RIP VERSION BOTH > SET USER Internal > SET IP FRAMING ETHERNET_II > SET IP RIP RECEIVE BO > SET IP RIP VERSION BOTH > SET USER Standard > SET PROFILE ID 000000000000 > SET PROFILE POWERUP ACTIVATE > SET PROFILE DISCONNECT KEEP > SET IP ROUTING ON > SET IP ADDRESS 0.0.0.0 > SET IP NETMASK 0.0.0.0 > SET IP FRAMING NONE > SET IP RIP RECEIVE V1 > SET IP RIP UPDATE OFF > SET IP RIP VERSION 1 > SET NETBIOS FILTER ON > SET USER amay128 > SET PROFILE ID 000000000000 > SET PROFILE POWERUP ACTIVATE > SET PROFILE DISCONNECT KEEP > SET BRIDGING OFF > SET 1 NUMBER 439xxxx > SET 2 NUMBER 439xxxx > SET IP ROUTING ON > SET IP ADDRESS 0.0.0.0 > SET IP NETMASK 0.0.0.0 > SET IP FRAMING NONE > SET IP RIP RECEIVE BO > SET IP RIP UPDATE OFF > SET IP RIP VERSION BOTH > SET NETBIOS FILTER ON > SET IP ROUTE DEST 0.0.0.0/0 GATEWAY 0.0.0.0 PROPAGATE ON COST 1 > CD > SET BUTTON amay128 > SET SERIALPORT CONFIG > LOGOUT > amay128> ? > CAll [ C# | L# | # | C#/L# | C#/# | #/# ] [ P# | CH# | P#/CH# ] [] > where > C# indicates a Connection number > # or L# indicates a Link number or D in case of the D channel link > C#/L# or #/# indicates Link of a Connection. Link should be D for D > channel li > nk > P# indicates Port > CH# indicates Channel > P#/CH# indicates Channel of a Port > CD [] > DEmand [] [THreshold=kb/s] [DUration=] [SOurce= WAN | LAn | > BOth] > DIsconnect [ C# | L# | # | C#/L# | C#/# #/# | P# | CH# | P#/CH# | ALl ] > where > C# indicates a Connection number > # or L# indicates a Link number or D in case of the D channel link > C#/L# or #/# indicates Link of a Connection. Link should be D for D > channel li > nk > P# indicates Port > CH# indicates Channel > P#/CH# indicates Channel of a Port > EStablish [] > HElp [ []] > IPxPIng ADdress | SErver > LOg > LOg NOne | CAlls | MEssage | ERrors | IPx [ TIme ] [ VErbose ] > LOg [ LAN | ] PAckets | TRaffic [CHannel = ] [ VErbose > [ I > Nbound | OUtbou > LOGIn | | | REmote > LOGOut > PIng > REBoot > RELease [] > REset ADdress = | ALl > REset CALLIdreceive | ALl > REset DIrectorynumber = [] | ALl > REset DHcp ADdress | ALl > REset [] FIlter = [ALl] > REset IP PAt POrthandler | ALl > REset IP FIlter | ALl > REset IP ROute ALl > REset IP ROute DEstination [/ ] [GAteway ] > REset IPX FIlter | ALl > REset IPX GAteway > REset IPX ROute ALl | DEstination= GAteway= > REset IPX SAp HElper > REset IPX SErvice ALl | NAme= TYpe= > REset [ | LAN ] PACkets [ ALl] > REset [] PATtern = [ALl] > REset PHONE1 | PHONE2 | DOV > REset SNmp TRaphost | ALl > REset TYpe = | ALl > REset USer > REset X25D POlicy [LSvc ] | ALl > SEt ACtive [] > SEt ADdress = > SEt AGe = | OFf > SEt ALawvoice ON | OFf > SEt AOcdtimeout ON [] | OFf > SEt AODi ON NUA= [ POwerupenable ] [ REversechargerequest ON | OFf ] > SEt AODi OFf > SHow AODi > SEt AUTODetection ON | OFF > SEt [] AUto = ON | OFf > SEt [] BAckupnumber = [ ] > SEt BAudrate 300 | 1200 | 2400 | 4800 | 9600 | 19200 | 38400 > SEt BRidging ON | OFf > SEt BIlling SPc | TImelink | NOne > SEt BUtton STandard | | OFf > SEt CALLDuration > SEt CALLErid ON | OFf > SEt CALLIdreceive > SEt CALLTime [VOice | DAta] INcoming | OUTgoing > > SEt CALLTime [VOice | DAta] INcoming | OUTgoing OFf > SEt CALLWaiting [ INterface = PHONE1 | PHONE2 ] ON | OFf > SEt CLIAuthentication OFf | ON [MInimummatch] > SEt CLICallback OFf | ON [] [DElay ] > SEt [] CLIValidatenumber = [ ] > SEt COmpression STac | OFf > SEt CONference > SEt COUntrygroup > SEt DAte MM/DD/YYYY > SEt DEfaults > SEt [] DELay = > SEt DHcp ADdress > SEt DHcp DNs PRimary | SEcondary > SEt DHcp DOmain [domain_name] > SEt DHcp GAteway PRimary | SEcondary > SEt DHcp LEasetime > SEt DHcp NEtmask > SEt DHcp NETBIOS_Scope [scope_id] > SEt DHcp SErver | RElay | OFf > SEt DHcp WIns PRimary | SEcondary > SEt [] DIrectorynumber = [] > SEt ECho ON | OFf > SEt FIlter []^8 [BLock | ACcept ] | [IGnore | DEmand ] > SEt GAteway > SEt INactive [] > SEt INTernaltones NOne | DIaltone | ALl > SEt IP > SEt IP ADdress > SEt IP COst > SEt IP FIlter ] > [DEstination = [NOT]]> | > ^8 > > SEt IP FRaming EThernet_II | NOne > SEt IP MUlticast ON | OFf > SEt IP PAt ON | OFf > SEt IP PAt POrthandler DEfault | TElnet | WIns | HTtp | SMtp | > FTp | | OFf > SEt IP PAt TCptimeout > SEt IP PAt UDptimeout > SEt IP NEtmask > SEt IP PRopagate ON | OFf > SEt IP RIp REceive BOth | V1 | V2 | OFf > SEt IP RIp SNapshot CLient ACtive QUiet UPdate OFf | ON > SEt IP RIp SNapshot SErver ACtive UPdate OFf | ON > SEt IP RIp SUmmarization AUto | OFf > SEt IP RIp TIme > SEt IP RIp UPdate PEriodic | LInkup | DEmand | SNapshot | TRiggered | OFf > SEt IP RIp VErsion 1 | 2 | BOTH > SEt IP ROUTE DEstination [/] GAteway > [ PRopagate ON | OFf ] [ COst ] > SEt IP ROUTIng ON | OFf > SEt IPX FIlter [TYpe = ] [SOcket = ] > [ NAme = ] ACcept | BLock > SEt IPX FIlter [TYpe = ] [SOcket = ] > [ NAme = ] ACcept | BLock > SEt IPX FRaming EThernet_II | 802.3 | 802.2 | SNap | NOne | UNKnown > SEt IPX GAteway USer > SEt IPX NETBios ACcept | BLock > SEt IPX NETWorkaddress > SEt IPX RIp REceive OFf | ON > SEt IPX RIp SNapshot CLient ACtive QUiet UPdate OFf | ON > SEt IPX RIp SNapshot SErver ACtive UPdate OFf | ON > SEt IPX RIp UPdate = PEriodic | DEmand | SNapshot | OFf > SEt IPX ROUTE DEstination= GAteway= > [HOps=] [COst=] > SEt IPX ROUTIng ON | OFf > SEt IPX SAp HElper > SEt IPX SErvice NAme= TYpe= > ADdress= [HOps=] > SEt IPX SPoofing | OFf > SEt IPX TRace | OFf | ON > SEt LEarn ON | OFf > SEt LOcalaccess ON | PArtial | PRotected > SEt LOGout > SEt [ ] LOOpback ON | OFf > SEt [ WAN | LAn ] MOde = ANy | ONly > SEt MUltidestination ON|OFF > SEt NETBios NAme SPoofing | OFf > SEt NETBios FIlter ON | OFf > SEt [] NUmber = [ ] > SEt PASSThru ON | OFf > SEt PAssword SYstem [ENcrypted] [] > SEt [PAttern = > ] > [OFfset = ] > [FRom = BEGINNING | TYPEFIELD | IPHDR | TCPHDR | UDPHDR | TCPDATA | > UDPDATA] > [PATTERNName = ] > SEt [] PErmanent ON | OFf > SEt PHONE1 | PHONE2 | DOV [] [] > SEt PLan NOrmal | INternational | NAtional | SUbscriber | > UNknown_isdn | ABbreviated | CEntrex | NEtwork > SEt PPp ADdress NEgotiation LOcal ON | OFF > SEt PPp AUthentication INcoming [ CHap ] [ PAp ] [ NOne ] > SEt PPp AUthentication OUtgoing [ CHap ] [ PAp ] [ NOne ] > SEt PPp AUthentication ACcept > SEt PPp BAcp ON | OFf > SEt PPp CAllback REQuest | REPly ON | OFf | ALways > SEt PPp CHAPAllow MUltihost ON | OFf > SEt PPp CHaprefuse ALl | NOne | > [INcall][REsponsefirst][SAmehost][DIrectionwrong > ] > SEt PPp CLientname [ ] > SEt PPp IP NEtmask LOcal ON | OFf > SEt PPp MAgicnumbercheck ON | OFf > SEt PPp MUltilink ON | OFf > SEt PPp MUltilink PPpheader ON | OFf > SEt PPp NEgotiation COunt > SEt PPp NEgotiation INtegrity | OFf > SEt PPp NEgotiation REtry > SEt PPp {ENcrypted] [] > SEt PPp TAS CEntral | DIstributed | OFf > SEt PPp TAS CLient > SEt PPp TAS CHapsecret LOcal ON | OFf > SEt PPp TErmreq COunt > SEt PROFile [POwerup=ACtivate|INactive] [DIsconnect=DEactivate|KEep] > [USer=] > SEt PROFile ID > SEt REmoteaccess OFF | PArtial | PRotected > SEt [] RIngback [] > SEt SCreenlength > SEt SErialPort COnfig | TPAD > SEt X25D LSvc NUA [NUI ] IDle > SEt X25D POlicy LSvc HOst TCP|UDP|ICMP [POrt xxxx] > [REversech > argerequest ON > SEt X25D TEI | ON | OFF > > SEt X25D PRiorityqueue LSvc DEfault HIgh|MEdium|NOrmal|LOw > SEt X25D PRiorityqueue LSvc LImit HIgh|MEdium|NOrmal|LOw > SEt X25D X121Host > SEt X25D POlicy LSvc HOst TCP|UDP|ICMP [POrt xxxx] > [REversech > argerequest ON > SEt X25D TEI | ON | OFF > > SEt X25D PRiorityqueue LSvc DEfault HIgh|MEdium|NOrmal|LOw > SEt X25D PRiorityqueue LSvc LImit HIgh|MEdium|NOrmal|LOw > SEt X25D X121Host > SEt SNmp COntact " contact string " > SEt SNmp LOcation " location string " > SEt SNmp TRap [ COldstart = ON | OFf ] [ WArmstart = ON | OFf ] > [ LInkup = ON | OFf ] [ LINKDown = ON | OFf ] [ AUthenticationfail = ON | > OFf ] > SEt SNmp TRAPHost > SEt SPeed 56k | 64k | AUto | VOice > SEt [] SPId = [] > SEt SUbnet > SEt SWitch 5ESS | DMS | NI-1 | PERM64 | PERM128 | PERM2X64 > SEt SYstemname [ ] > SEt TIme HH:MM:SS > SEt TIMEOut [ | OFf > SEt TYpe = [ ACcept | BLock ] [ IGnore | DEmand ] > SEt TRansfer > SEt TPad PArity EVen | ODd | NOne | MAsk > SEt UNicastfilter ON|OFF > SEt USer [] [ INcoming | OUtgoing ] > SEt VOicepriority [ INcoming | OUtgoing ] [ INTerface = PHONE1 | PHONE2 ] > NEver | COnditional | ALways > SEt X25 [LIc | HIc | LTc | HTc | LOc | HOc] > SHow > SHow [] ADdress > SHow CALLDuration > SHow CALLTime > SHow COnfig | NEgotiation | SEcurity [ALl] > SHow CONNections | DEmand | ETher | VOicerouting | STatus | TImeout > SHow DHcp Config > SHow [ ] FIlter > SHow IP COnfig | FIlter | ROute [ALl] > SHow IP PAt > SHow IP RIp SNapshot [ALl] > SHow IP RIp TIme > SHow IPX COnfig | ROute | SErvice [ALl] > SHow IPX CONNections| DEmand | STatistics > SHow IPX FIlter [ALl] > SHow IPX RIp SNapshot [ALl] > SHow MEmstats | SNmp | TYpe > SHow NETBios NAme > SHow [ | LAn ] PAckets > SHow [ ] PATtern > SHow PRofile | USers > SHow TPad > SHow X25 > SHow X25D POlicy > SHow X25D STatistics > SHow X25D TEI > SHow X25D PRiorityqueue COnfig > SHow X25D X121HOST > SHow X25D POlicy > SHow X25D STatistics > SHow X25D TEI > SHow X25D X121HOST > SHow X25D PRiorityqueue COnfig > SWl > SWl TFTP > SWl TFTP COnfig > SWl TFTP > SWl TFTP COnfig > TEst [ STop | REsult | ETher ] > TEst [ ] [ WAn | ALl ] > TEst MAxpkts > TEst MInpkts > TEst RAte > TEst POts RIng [cadence] > TImeout [THreshold=] [DUration=] [SOurce= WAn | LAn | > BOth] > UNlearn [] > UNset [] AUto > UNset CALLErid | COmpression > UNset [] DEmand | TIMEOut > UNset LEarn | PASSThru | SPeed | BRidging > UNset [] NUmber | RIngback > UNset [] PErmanent > UNset PPp AUthentication > UNset PPp CAllback > UNset PPp PAssword HOst > UNset PPp SEcret HOst > UPload > UPload TFTP > VErsion > > > ----- Original Message ----- > From: anil > To: > Sent: Friday, November 23, 2001 5:23 AM > Subject: RE: Cisco 700 series in Remote Access exam (640-505) [7:26975] > > > > The 1st router I ever set up was the Cisco 765. > > At that time (3 years ago) it did *not* run the CISCO IOS. > > I guess it still does not run the IOS. > > It runs/ran a quirky version of the IOS. > > So any questions they would ask you about the 7xx series would have to > take > > that into account (I guess). > > Hope this helps > > -Anil > > > > > > -----Original Message----- > > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] > > Sent: Friday, November 23, 2001 12:38 AM > > To: [EMAIL PROTECTED] > > Subject: RE: Cisco 700 series in Remote Access exam (640-505) [7:26975] > > > > > > Hai, > > > > I just taken BCRAN 20/11/01, on my exam there was no Cisco 700. Even when > I > > took the BCRAN tranning from cisco tranning center, they skip the subject. > > > > > > > ---------- > > > From: [EMAIL PROTECTED][SMTP:[EMAIL PROTECTED]] > > > Reply To: [EMAIL PROTECTED] > > > Sent: Wednesday, November 21, 2001 4:29 PM > > > To: [EMAIL PROTECTED] > > > Subject: Cisco 700 series in Remote Access exam (640-505) [7:26975] > > > > > > Hello, > > > > > > (This is my first post in this wonderful newsgroup) > > > > > > > > > Will the said content (700 series router) still tested on the real > > > test? > > > I'll take the test on next week. > > > > > > And it still occupied one chapter in the book "CCNP remote access > > > exam > > > certification Guide", but not on the exam topics published by Cisco.. > > > > > > Any folks taken the exam recently can share the experiences? > > > > > > Thanks a lot :> > > > > > > > > > Regards, > > > c.h.Ip > > > > > > > > > > > > ps. Any people in Hong Kong here? want to find one or more study > > > parthers~ Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=27645&t=26975 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]