Please ignore my questions. I mailed the e-mail two days ago, but got the answer a couple of hours later from a different list. I mailed a new one with the answers the same day informing about this, but it apparently got on the list before this one.
Thanks, Ole ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Ole Drews Jensen Systems Network Manager CCNP, MCSE, MCP+I RWR Enterprises, Inc. [EMAIL PROTECTED] ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ http://www.RouterChief.com ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ NEED A JOB ??? http://www.oledrews.com/job ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ -----Original Message----- From: Ole Drews Jensen [mailto:[EMAIL PROTECTED]] Sent: Wednesday, January 23, 2002 9:22 PM To: [EMAIL PROTECTED] Subject: PIX 501 : Interface Speed & PDM access [7:32929] Good morning (afternoon or night depending on your location), I just received my PIX 501 with 10 user license, 3DES and version 6.1(1). A couple of questions: The 4 port inside interface should be 10/100, but if I try to change it from 10, I get this message: PIX501(config)# interface ethernet1 100full ethernet1 interface can only be set to 10full. Type help or '?' for a list of available commands. What's up with that? Also, I went on my Cisco 3548 and forced the port which the PIX 501 is connected to in 100/FULL mode, and the 100 MBPS LED lit up on the inside interface port 1 on the PIX. BUT, when I do a show interface, it still says 10 Mbps: interface ethernet1 "inside" is up, line protocol is up Hardware is i82559 ethernet, address is 0008.a32b.8e7f IP address 10.5.0.1, subnet mask 255.0.0.0 MTU 1500 bytes, BW 10000 Kbit full duplex 3305 packets input, 376387 bytes, 0 no buffer Received 2571 broadcasts, 0 runts, 0 giants 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 962 packets output, 70817 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 babbles, 0 late collisions, 0 deferred 0 lost carrier, 0 no carrier input queue (curr/max blocks): hardware (128/128) software (0/2) output queue (curr/max blocks): hardware (1/2) software (0/1) I am confused here - are there a BIG bug in 6.1(1)????? Next, I can telnet to the PIX after I added my workstations ip address to the allowed telnetters, but I cannot seem to get in contact with it from my browser so I can use the PDM. As you can see below, I do have "http server enable" and "http 0.0.0.0 0.0.0.0 inside". Some info: The PIX inside interface = 10.5.0.1 / 8 My workstation = 10.10.10.10 / 8 Cisco PIX Firewall Version 6.1(1) Cisco PIX Device Manager Version 1.1(2) Licensed Features: Failover: Disabled VPN-DES: Enabled VPN-3DES: Enabled Maximum Interfaces: 2 Cut-through Proxy: Enabled Guards: Enabled Websense: Enabled Inside Hosts: 10 Throughput: Limited ISAKMP peers: 5 nameif ethernet0 outside security0 nameif ethernet1 inside security100 hostname PIX501 fixup protocol ftp 21 fixup protocol http 80 fixup protocol h323 1720 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol sip 5060 fixup protocol skinny 2000 names interface ethernet0 10baset interface ethernet1 10full mtu outside 1500 mtu inside 1500 ip address outside dhcp setroute ip address inside 10.5.0.1 255.0.0.0 ip audit info action alarm ip audit attack action alarm pdm logging informational 100 pdm history enable arp timeout 14400 timeout xlate 0:05:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h323 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout uauth 0:05:00 absolute aaa-server TACACS+ protocol tacacs+ aaa-server RADIUS protocol radius http server enable http 0.0.0.0 0.0.0.0 inside no snmp-server location no snmp-server contact snmp-server community public no snmp-server enable traps floodguard enable no sysopt route dnat telnet 10.10.10.10 255.255.255.255 inside telnet timeout 5 ssh timeout 5 dhcpd lease 3600 dhcpd ping_timeout 750 dhcpd auto_config outside terminal width 80 I have tried with http 10.10.10.10 255.255.255.255 inside, but that didn't make a difference. Does anyone have a magic trick here? Thanks in advance, and sorry if these questions might seem stupid. Ole ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Ole Drews Jensen Systems Network Manager CCNP, MCSE, MCP+I RWR Enterprises, Inc. [EMAIL PROTECTED] ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ http://www.RouterChief.com ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ NEED A JOB ??? http://www.oledrews.com/job ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=33189&t=32929 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]