hmm, I'll be interested to see what happens. In case your wondering why in the world, it was a channelized T3 so the link was really another parallel T1 but to EIGRP the interface was 45M.
Dave Cisco Nuts wrote: > > So based on your experience, if I set the bandwidth on one route to 45mb and > leave the other as the default, variance of 2 will work, right? I'll try > that and let you know. > Thanks! > > >From: "MADMAN" > >Reply-To: "MADMAN" > >To: [EMAIL PROTECTED] > >Subject: Re: Variance for Eigrp...does it actually work?? [7:33835] > >Date: Thu, 31 Jan 2002 11:14:46 -0500 > > > >I'm not going to attempt to explain the mathmatics but the last time I > >needed to use variance, get EIGRP to loadshare over a T1 and T3 a > >variance of 2 worked perfectly. > > > > Dave > > > >John Neiberger wrote: > > > > > > I don't really have an answer, this is more of a "me too" email. I've > > > only bothered with variance once in a practice lab and I was not able to > > > make it work even after setting the variance to a ridiculously high > > > number. No matter what I did, I was not able to get both EIGRP routes > > > into the routing table. > > > > > > At some point I need to go back and figure out why it wasn't working > > > but I've been avoiding it. > > > > > > John > > > > > > >>> "Cisco Nuts" 1/31/02 12:05:03 AM >>> > > > Hello,I am testing out the variance command under eigrp and it does > > > not > > > seem to be working the way it is explained in the CCNP routing guide > > > by > > > CiscoPress. Any ideas ? Sorry, Long post but need help.I have RTA > > > connected to RTB and RTC via FR physical intf. running eigrp 1RTB and > > > RTC > > > are connected to BBR via serials also running eigrp 1BBR is connected > > > to > > > TS via serial running eigrp 1 and igrp 1TS is connected to REMOTE > > > running > > > rip.RTA to RTB to BBR have bandwidth = 64 configed.RTA to RTC to BBR > > > have > > > the default bw = 1.544On RTA, the route to Rip netw. 12. and 13. on > > > Remote show up via the RTC to BBR to TS to Remote route....which is > > > correct.D EX 12.0.0.0/8 [170/3245056] via 192.168.10.243, 00:12:37, > > > Serial0 > > > D EX 13.0.0.0/8 [170/3245056] via 192.168.10.243, 00:13:42, Serial0 > > > The > > > metric via RTB to BBR to TS to Remote is 41538560 as inD EX 12.0.0.0/8 > > > [170/41538560] via 192.168.10.242, 00:00:17, Serial0 > > > D EX 13.0.0.0/8 [170/41538560] via 192.168.10.242, 00:00:17, Serial0 > > > After > > > doing the math,( multiplied 3245056 x 13 to get 42185728 which is > > > greater > > > than 41538560), I configed a variance of 13 on RTA and expected to see > > > 2 > > > routes to networks 12. and 13. but only 1 route shows up, that thru > > > RTC.Is > > > there a reason why?Thank you. : > > > > > > ------------------------------------------------------------------------ > > > > > > Send and receive Hotmail on your mobile device: Click Here > >-- > >David Madland > >Sr. Network Engineer > >CCIE# 2016 > >Qwest Communications Int. Inc. > >[EMAIL PROTECTED] > >612-664-3367 > > > >"Emotion should reflect reason not guide it" > _________________________________________________________________ > Chat with friends online, try MSN Messenger: http://messenger.msn.com -- David Madland Sr. Network Engineer CCIE# 2016 Qwest Communications Int. Inc. [EMAIL PROTECTED] 612-664-3367 "Emotion should reflect reason not guide it" Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=33935&t=33835 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]