Double click on a packet. Save Packet in the File Menu. Save as text. ;-) Priscilla
At 01:39 PM 2/15/02, John Neiberger wrote: >Perhaps there is some confusion about the term 'Target ARP'. In an ARP >packet, the destination MAC address in the ethernet header is all Fs. >The Target Hardware Address is all zeroes. Take a look: > >Ethernet Header >-------------------------- >Destination: FF:FF:FF:FF:FF:FF Ethernet Broadcast >Source: 00:04:AC:4C:5D:F3 >Protocol Type: 0x0806 IP ARP > >ARP - Address Resolution Protocol >-------------------------------------------------------- >Hardware: 1 Ethernet (10Mb) >Protocol: 0x0800 IP >Hardware Address Length: 6 >Protocol Address Length: 4 >Operation: 1 ARP Request >Sender Hardware Address: 00:04:AC:4C:5D:F3 >Sender Internet Address: 10.1.103.20 >Target Hardware Address: 00:00:00:00:00:00 (ignored) >Target Internet Address: 10.1.103.52 > >On a related note, I just discovered that it is a major pain to copy a >packet capture from Etherpeek!! If any of you know how to copy an >entire packet as text, please let me know. :-) > >John > > >>> "Priscilla Oppenheimer" 2/15/02 11:13:41 AM > >>> >I assume you read it wrong. It's a packet captured from a network, >unedited. > >At 09:05 PM 2/14/02, Andy Barkl wrote: > >Priscilla, first of all thank you for the use of your CIT flash >cards. > >Secondly, in the following question, > >http://www.priscilla.com/cit/general/answer14.html it indicates that >a > >target ARP address is all 0s. This was confusing when I saw it >because > >my understanding is that a target ARP is all Fs. > >Can you clarify this? I assume it's simply a typo. > > > >Thank you. > > > > > > > >-----Original Message----- > >From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf >Of > >Priscilla Oppenheimer > >Sent: Thursday, February 14, 2002 4:08 PM > >To: [EMAIL PROTECTED] > >Subject: Re: Off topic but somehow interesting problem [7:35426] > > > >At 03:39 PM 2/14/02, Patrick Ramsey wrote: > > >arp is an ethernet protocol...not in the ip stack per se... (even > >though I > > >think Microsoft install arp with it's ip stack) > > > >ARP is defined in RFC 826. In other words, it's defined by the same > >standards body that defines IP protocols. ARP is used to map IP > >addresses > >to data-link-layer addresses. It's an essential component of an IP > >implementation. But let's not get into one of those arguments again. >;-) > > > >The original poster says that the sender is setting its own > >data-link-layer > >address to FF FF FF FF FF FF. This would indicate a major bug in the > >driver. > > > >It makes one wonder if the poster is misinterpreting the protocol > >analyzer > >output? Can you send it to us?? Sorry, if this assumption is wrong >but > >the > >error that you report is so bizarre, we have to wonder..... > > > >Priscilla > > >________________________ > >Priscilla Oppenheimer >http://www.priscilla.com ________________________ Priscilla Oppenheimer http://www.priscilla.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=35528&t=35426 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]