There were some bugs with 12.0(5) with regards to hyperterm, causing the switch to reboot was one of them. Try upgrading.
----- Original Message ----- From: "Ismail Al-Shelh" To: Sent: Saturday, March 09, 2002 9:12 AM Subject: 2950-24 giving me strange symbols [7:37724] > Hello all > I have two Cat 2950-24 switches , when I connect to the first switch > through hyper terminal , something strange happening to me , that strange > thing is when I try to type any letter on the keyboard it gives me another > letter or symbols I do not know why this is happening !!!! the only thing I > can see is when one of the fastethernet port state is up or down but its > not allowing me to write proper letters , I tried to plug the cable out and > plug it again it gives me the following > > C2950 Boot Loader (CALHOUN-HBOOT-M) Version 12.0(5.3)WC(1), MAINTENANCE > INTERIM > SOFTWARE > Compiled Mon 30-Apr-01 07:56 by devgoyal > WS-C2950-24 starting... > Base ethernet MAC Address: 00:07:ec:02:67:00 > Xmodem file system is available. > Initializing Flash... > flashfs[0]: 161 files, 2 directories > flashfs[0]: 0 orphaned files, 0 orphaned directories > flashfs[0]: Total bytes: 7741440 > flashfs[0]: Bytes used: 2960896 > flashfs[0]: Bytes available: 4780544 > flashfs[0]: flashfs fsck took 6 seconds. > ...done initializing flash. > Boot Sector Filesystem (bs:) installed, fsid: 3 > Parameter Block Filesystem (pb:) installed, fsid: 4 > Loading > "flash:c2950-c3h2s-mz.120-5.3.WC.1.bin"...############################## > ############################################################################ > #### > ################# > > File "flash:c2950-c3h2s-mz.120-5.3.WC.1.bin" uncompressed and installed, > entry p > oint: 0x80010000 > executing... > > Restricted Rights Legend > > Use, duplication, or disclosure by the Government is > subject to restrictions as set forth in subparagraph > (c) of the Commercial Computer Software - Restricted > Rights clause at FAR sec. 52.227-19 and subparagraph > (c) (1) (ii) of the Rights in Technical Data and Computer > Software clause at DFARS sec. 252.227-7013. > > cisco Systems, Inc. > 170 West Tasman Drive > San Jose, California 95134-1706 > > > > Cisco Internetwork Operating System Software > IOS (tm) C2950 Software (C2950-C3H2S-M), Version 12.0(5.3)WC(1), MAINTENANCE > INT > ERIM SOFTWARE > Copyright (c) 1986-2001 by cisco Systems, Inc. > Compiled Mon 30-Apr-01 07:56 by devgoyal > Image text-base: 0x80010000, data-base: 0x8031A000 > > > Initializing flashfs... > flashfs[1]: 161 files, 2 directories > flashfs[1]: 0 orphaned files, 0 orphaned directories > flashfs[1]: Total bytes: 7741440 > flashfs[1]: Bytes used: 2960896 > flashfs[1]: Bytes available: 4780544 > flashfs[1]: flashfs fsck took 6 seconds. > flashfs[1]: Initialization complete. > Done initializing flashfs. > C2950 POST: System Board Test : Passed > C2950 POST: Ethernet Controller Test : Passed > C2950 POST: MII TEST : Passed > > cisco WS-C2950-24 (RC32300) processor (revision B0) with 22260K bytes of > memory. > > Processor board ID FAB0544P2EE > Last reset from system-reset > > Processor is running Enterprise Edition Software > Cluster command switch capable > Cluster member switch capable > 24 FastEthernet/IEEE 802.3 interface(s) > > 32K bytes of flash-simulated non-volatile configuration memory. > Base ethernet MAC Address: 00:07:EC:02:67:00 > Motherboard assembly number: 73-5781-08 > Motherboard serial number: FAB0544789W > Model revision number: B0 > Model number: WS-C2950-24 > System serial number: FAB0544P2EE > C2950 INIT: Complete > > 00:00:17: %SYS-5-RESTART: System restarted -- > Cisco Internetwork Operating System Software > IOS (tm) C2950 Software (C2950-C3H2S-M), Version 12.0(5.3)WC(1), MAINTENANCE > INT > ERIM SOFTWARE > Copyright (c) 1986-2001 by cisco Systems, Inc. > Compiled Mon 30-Apr-01 07:56 by devgoyal > > --- System Configuration Dialog --- > > At any point you may enter a question mark '?' for help. > Use ctrl-c to abort configuration dialog at any prompt. > Default settings are in square brackets '[]'. > > Continue with configuration dialog? [yes/no]: oo4[j}~}{|u > > > > As you see I was trying to say NO but this No came to be oo4[j}~}{|u , > please somebody tell me the secret. > > Note: I do not have any problem with the second switch I can easily login to > the user exec mode and configure it. > > Ismail Al-shelh. > > [GroupStudy.com removed an attachment of type application/ms-tnef] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=37725&t=37724 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]