Here is the 2600 password recovery page and below it the home page for password recovery:
http://www.cisco.com/warp/public/474/pswdrec_2600.shtml http://www.cisco.com/warp/public/474/ Dave Rao Cisco wrote: > Hi Biswajeet, > > This is the URL for the Password Recovery Procedure. > > http://www.cisco.com/warp/public/474/pswdrec_2500.html#proc > > ( I am not sure the above link will be useful or not, as the password > recovery procedure for 2600 routers are not available from CISCO website) > > But suggest go thru the following tips. > > The tips are > 9600 baud rate > No parity > 8 data bits > 1 stop bit > No flow control > > II tip (This worked for me) > This is useful if your terminal emulator doesn't support the break key, or > if a bug prevents it from sending the correct signal (the hyperterminal > under Windows NT used to suffer from this behavior): > > Connect to the router with the following terminal settings: > 1200 baud rate > No parity > 8 data bits > 1 stop bit > No flow control > > You no longer see any output on your screen. This is normal. > > Power cycle (switch off and then on) the router and press the spacebar for > 10-15 seconds. This generates a signal similar to the break sequence. > > Disconnect your terminal and reconnect with a 9600 baud rate. You should now > be in ROM Monitor mode. > > > For the keyboard combinations are - depending on Operating System follow > this link and let me know if this is of some help. > http://www.cisco.com/warp/public/701/61.html#break-key > > Good luck > Raocisco > [EMAIL PROTECTED] M. Labiro wrote: > > > > The router is looking for a config file on a TFTP server > > by broadcasting messages. You can disable this behaviour by > > "no service config" command. > > > > HTH > > > > > Hi, > > > Need Help in understanding why the following problem is > > occuring. > > > When I connect the CISCO 2600 router through the console > > port. I get the > > > following error message > > > > > > %Error opening tftp://255.255.255.255/network-confg (Timed > > out) > > > %Error opening tftp://255.255.255.255/cisconet.cfg (Timed out) > > > %Error opening tftp://255.255.255.255/SHG_RTR-confg (Timed > > out) > > > %Error opening tftp://255.255.255.255/SHG_RTR.cfg (Timed out) > > > > > > And because of this sometimes I cannot ping or telnet the > > router. > > > > > > When I boot it I get the following message > > > > > > > > > ############################################################################ > > #### > > > > > > ############################################################################ > > #### > > > > > > ############################################################################ > > #### > > > ############## [OK] > > > > > > Restricted Rights Legend > > > > > > Use, duplication, or disclosure by the Government is > > > subject to restrictions as set forth in subparagraph > > > (c) of the Commercial Computer Software - Restricted > > > Rights clause at FAR sec. 52.227-19 and subparagraph > > > (c) (1) (ii) of the Rights in Technical Data and Computer > > > Software clause at DFARS sec. 252.227-7013. > > > > > > cisco Systems, Inc. > > > 170 West Tasman Drive > > > San Jose, California 95134-1706 > > > > > > > > > > > > Cisco Internetwork Operating System Software > > > IOS (tm) C2600 Software (C2600-I-M), Version 12.0(7)T, > > RELEASE SOFTWARE > > > (fc2) > > > Copyright (c) 1986-1999 by cisco Systems, Inc. > > > Compiled Tue 07-Dec-99 02:12 by phanguye > > > Image text-base: 0x80008088, data-base: 0x807AAF70 > > > > > > cisco 2620 (MPC860) processor (revision 0x102) with > > 26624K/6144K bytes of > > > memory > > > FAQ, list archives, and subscription info: > > http://www.groupstudy.com/list/cisco.html > > > Report misconduct and Nondisclosure violations to > > [EMAIL PROTECTED] -- David Madland CCIE# 2016 Sr. Network Engineer Qwest Communications Inc. 612-664-3367 [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=39265&t=39130 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
