Cool! I will spend sometime today learning how to use the bug tool... Thanks,
Pierre-Alex -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] Sent: Sunday, March 31, 2002 12:00 PM To: [EMAIL PROTECTED] Subject: RE: Logging - terminal monitor not working [7:39957] Have seen it on many (mostly smaller) routers. Its a bug: > > ## Bug Id : CSCdu60369 > > ## Headline no syslog logging when logging synchronous enabled > > ## Product c2600 Model > > ## Component os-logging Duplicate of > > ## Severity 2 Status M > > ## Version Found 12.0(7)T 12.0(6)S Fixed-in Version 12.2(5) > > ## Release Notes > > ## > > ## The logging synchronous line configuration command may > > ## cause logging to stop. > > ## > > ## Workaround: Remove this command. hth Reinhold Pierre-Alex Guanel wrote: > > Amazing!!!! I removed logging synchronous on line console 0 > and debug > worked .... > > I am curious, what is the reason for "logging synchronous" > preventing debug > outputs > > on terminal lines? > > Pierre-Alex > > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On > Behalf Of > Lidiya White > Sent: Saturday, March 30, 2002 5:46 PM > To: [EMAIL PROTECTED] > Subject: RE: Logging - terminal monitor not working [7:39957] > > > I would add "no ip route-cache" on that interface and make sure > that you > don't have "logging synchronous" under line con 0... > > -- Lidiya White > > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On > Behalf Of > Pierre-Alex Guanel > Sent: Saturday, March 30, 2002 3:04 PM > To: [EMAIL PROTECTED] > Subject: Logging - terminal monitor not working [7:39957] > > Kind of a silly problem but can't figure it out ... > > I am connected to R1 via telnet. I have turned on debugging of > ip > packets > > I also have issued the command "terminal monitor" > > Yet I do not get anything logged when I ping the Ethernet > interface of > R1 > > Any ideas? > > Thanks > > ============================ > > R1#sh terminal > Line 2, Location: "", Type: "ANSI" > Length: 45 lines, Width: 80 columns > Baud rate (TX/RX) is 9600/9600 > Status: Ready, Active, No Exit Banner > Capabilities: Receives Logging Output > Modem state: Ready > Group codes: 0 > Special Chars: Escape Hold Stop Start Disconnect Activation > ^^x none - - none > Timeouts: Idle EXEC Idle Session Modem Answer Session > Dispatch > never never > none not > set > Idle Session Disconnect Warning > never > Login-sequence User Response > 00:00:30 > Autoselect Initial Wait > not set > Modem type is unknown. > Session limit is not set. > Time since activation: 00:41:15 > Editing is enabled. > History is enabled, history size is 10. > DNS resolution in show commands is enabled > Full user help is disabled > Allowed transports are lat pad v120 mop telnet rlogin nasi. > Preferred > is > lat. > No output characters are padded > No special data dispatching characters > > ============================================================ > R1#sh logging > Syslog logging: enabled (0 messages dropped, 0 flushes, 0 > overruns) > Console logging: level debugging, 102 messages logged > Monitor logging: level debugging, 2 messages logged > Logging to: vty2(0) > Buffer logging: level debugging, 102 messages logged > Trap logging: level informational, 47 message lines logged > > Log Buffer (4096 bytes): Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=39991&t=39957 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
