Hi All, I have a problem with a 3600 with a nm-8am (8port analog modem card v.34) for dial-up clients. The speed for the connection is never more than 21.6k TX and 19.2k RX. Connetction works fine, only slow. Belief me I read all documention on CCO and now answers for this one. I try all the modemcaps, and play with the mics init string, with no luck. Does anyone know what "Call Handle failed for Modem 2/1" means??? Where is my problem?? I exculded the Telco and dial in straight through the PABX(analog). Same problem... When I use "debug confmoden" and "debug modem" I get the following:
*Mar 1 03:45:18.303: Modem 2/1 Mcom: in modem state 'Dialing/Answering' *Mar 1 03:45:18.959: Modem 2/1 Mcom: in modem state 'Incoming ring' *Mar 1 03:45:21.231: Modem 2/1 Mcom: in modem state 'Waiting for Carrier' *Mar 1 03:45:33.447: Modem 2/1 Mcom: in modem state 'Connected' *Mar 1 03:45:34.059: Call Handle failed for Modem 2/1 *Mar 1 03:45:34.059: Modem 2/1 Mcom: CONNECT at 21600/14400(Tx/Rx), V34, LAPM, V42bis, Answer *Mar 1 03:45:34.343: TTY66: DSR came up *Mar 1 03:45:34.343: tty66: Modem: IDLE->(unknown) *Mar 1 03:45:34.343: TTY66: EXEC creation *Mar 1 03:45:34.343: TTY66: set timer type 10, 30 seconds *Mar 1 03:45:36.435: TTY66: Autoselect(2) sample 7E *Mar 1 03:45:36.435: TTY66: Autoselect(2) sample 7EFF *Mar 1 03:45:36.435: TTY66: Autoselect(2) sample 7EFF7D *Mar 1 03:45:36.435: TTY66: Autoselect(2) sample 7EFF7D23 *Mar 1 03:45:36.435: TTY66 Autoselect cmd: ppp negotiate *Mar 1 03:45:36.435: TTY66: EXEC creation *Mar 1 03:45:36.435: TTY66: create timer type 1, 600 seconds *Mar 1 03:45:36.567: TTY66: destroy timer type 1 *Mar 1 03:45:36.567: TTY66: no timer type 0 to destroy *Mar 1 03:45:39.311: Modem 2/1 Mcom: switching to PPP mode *Mar 1 03:45:39.311: Modem 2/1 Mcom: PPP escape map: Tx map = FFFFFFFF, Rx map = 0 *Mar 1 03:45:39.311: Modem 2/1 Mcom: PPP escape map: Tx map = FFFFFFFF, Rx map = 0 03:45:39: %LINK-3-UPDOWN: Interface Async66, changed state to up *Mar 1 03:45:39.527: Modem 2/1 Mcom: PPP escape map: Tx map = 0, Rx map = 0 *Mar 1 03:46:14.675: Modem 2/1 Mcom: in modem state 'Disconnecting' *Mar 1 03:46:14.679: Modem 2/1 Mcom: DISCONNECT, duration = 00:00:42, reason (0 xE) Remote Link Disc *Mar 1 03:46:15.343: TTY66: DSR was dropped *Mar 1 03:46:15.343: tty66: Modem: READY->(unknown) *Mar 1 03:46:16.047: Modem 2/1 Mcom: in modem state 'Idle' *Mar 1 03:46:16.343: TTY66: dropping DTR, hanging up *Mar 1 03:46:16.343: TTY66: Async Int reset: Dropping DTR *Mar 1 03:46:16.343: tty66: Modem: HANGUP->(unknown) *Mar 1 03:46:16.487: Modem 2/1 Mcom: PPP escape map: Tx map = FFFFFFFF, Rx map = 0 *Mar 1 03:46:17.343: TTY66: cleanup pending. Delaying DTR *Mar 1 03:46:18.343: TTY66: cleanup pending. Delaying DTR *Mar 1 03:46:18.487: Modem 2/1 Mcom: PPP escape map: Tx map = FFFFFFFF, Rx map = 0 *Mar 1 03:46:19.343: TTY66: cleanup pending. Delaying DTR *Mar 1 03:46:20.343: TTY66: cleanup pending. Delaying DTR *Mar 1 03:46:21.343: Modem 2/1 Mcom: switching to character mode *Mar 1 03:46:21.343: TTY66: no timer type 0 to destroy *Mar 1 03:46:21.343: TTY66: no timer type 1 to destroy *Mar 1 03:46:21.343: TTY66: no timer type 3 to destroy *Mar 1 03:46:21.343: TTY66: no timer type 4 to destroy *Mar 1 03:46:21.343: TTY66: no timer type 2 to destroy *Mar 1 03:46:21.343: Async66: allowing modem_process to continue hangup *Mar 1 03:46:21.343: TTY66: restoring DTR *Mar 1 03:46:21.343: TTY66: autoconfigure probe started *Mar 1 03:46:21.343: TTY66: Modem ommand: --AT&F&FS0=1S0=1&C1&D3\Q3\J0\N3%M2% U2%G1$B38400%B33600-- *Mar 1 03:46:23.919: TTY66: Modem configuration succeeded *Mar 1 03:46:23.919: TTY66: Detected modem speed 9600 *Mar 1 03:46:23.919: TTY66: Done with modem configuration 03:47:06: %LINK-3-UPDOWN: Interface Async66, changed state to down Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=49679&t=49679 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]