Hi, professionals. I'm trying to connect two Cisco 3600 router with OC3 Multimode interface (NM-1A-OC3MM) in a back-to-back fashion using IOS 12.2(8)T.
[Router 1 ATM 1/0] [Router 2 ATM 1/0] Basically, my link flaps and cannot establish a stable connection. Configuration is done in such a way that.. router #1 ------------ interface ATM1/0 no ip address no atm ilmi-keepalive ! interface ATM1/0.200 point-to-point ip address 2.2.2.2 255.255.255.0 pvc 200/200 protocol ip 2.2.2.1 broadcast ! router #2 --------------- interface ATM1/0 no ip address no atm ilmi-keepalive ! interface ATM1/0.200 point-to-point ip address 2.2.2.1 255.255.255.0 pvc 200/200 protocol ip 2.2.2.2 broadcast ! Does anyone have any idea if I am missing in the configuration? Anybody have any experience in OC3 MM link flapping? Please help. Thanks in advance. -Paul Below is output dump from my router #1 with 'debug atm events' on. Router#debug atm events ATM events debugging is on Router# Router# Router# 00:46:00: %LINK-3-UPDOWN: Interface ATM1/0, changed state to up 00:46:00: atmoc3_cstate(ATM1/0): state=4 atm_lineup=0 00:46:00: atmoc3_state_change(ATM1/0): restarting 28 VCs 00:46:00: rs8234_setup_vc(ATM1/0): vc:2 vpi:200 vci:200 00:46:00: peak rate configured is 155000000 00:46:00: rs8234_setup_vc_common() VCD=2 vp/vc=200/200 etype=0 00:46:00: rs8234_open_connection_seg 00:46:00: vcd:2 00:46:00: vcc_id:166 00:46:00: ds->p_vcd_table[ccb_ptr->vcd].host_vccid:166 00:46:00: ccb_ptr->av_bit_rate:0 00:46:00: ccb_ptr->cdvt:0 00:46:00: ccb_ptr->peak_bit_rate:148772272 00:46:00: p_host_seg_vc_table:0x82A6C910: 00:46:00: aal type word value 0x80100080. 00:46:00: rs8234_setup_cos(ATM1/0): vc:2 wred_name:- max_q:0 00:46:00: %ATM-5-UPDOWN: Changing VC 200/200 VC-state to PVC activated. 00:46:02: %LINK-3-UPDOWN: Interface ATM1/0, changed state to down 00:46:02: atmoc3_cstate(ATM1/0): state=0 atm_lineup=1 00:46:02: Resetting ATM1/0 00:46:02: rs8234_teardown_vc(ATM1/0): vc:2 vpi:200 vci:200 00:46:02: Status and ptr is 0 Status Q is 0 00:46:02: %ATM-5-UPDOWN: Changing VC 200/200 VC-state to PVC deactivated. 00:46:22: %LINK-3-UPDOWN: Interface ATM1/0, changed state to up 00:46:22: atmoc3_cstate(ATM1/0): state=4 atm_lineup=0 00:46:22: atmoc3_state_change(ATM1/0): restarting 28 VCs 00:46:22: rs8234_setup_vc(ATM1/0): vc:2 vpi:200 vci:200 00:46:22: peak rate configured is 155000000 00:46:22: rs8234_setup_vc_common() VCD=2 vp/vc=200/200 etype=0 00:46:22: rs8234_open_connection_seg 00:46:22: vcd:2 00:46:22: vcc_id:167 00:46:22: ds->p_vcd_table[ccb_ptr->vcd].host_vccid:167 00:46:22: ccb_ptr->av_bit_rate:0 00:46:22: ccb_ptr->cdvt:0 00:46:22: ccb_ptr->peak_bit_rate:148772272 00:46:22: p_host_seg_vc_table:0x82A6C968: 00:46:22: aal type word value 0x80100080. 00:46:22: rs8234_setup_cos(ATM1/0): vc:2 wred_name:- max_q:0 00:46:22: %ATM-5-UPDOWN: Changing VC 200/200 VC-state to PVC activated. 00:46:24: %LINK-3-UPDOWN: Interface ATM1/0, changed state to down Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=53134&t=53134 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]