HI, all Thnaks for the help.It has workd.
----- Original Message ----- From: "Osama Kamal" To: Sent: Sunday, October 13, 2002 1:54 PM Subject: RE: X.25 [7:55369] > Try to remove the x25 address from each interface and remove the current > routes, the new routes should reflect the actual physical connectivity for > example: > > x25 route 8888 interface Serial2/0 > x25 route 4401 interface Serial2/1 > x25 route 3333 interface Serial2/3 > ..... > .... > ... > > > Osama Kamal > > -----Original Message----- > From: Niraj somaiya [mailto:niraj.somaiya@;nirmaldatacomm.com] > Sent: Friday, October 11, 2002 3:27 PM > To: [EMAIL PROTECTED] > Subject: X.25 [7:55369] > > HI all > > NEED YOUR HELP URGENTLY!!!ANY X.25 EXPERTS LISTENING...... > I have installed cisco 3640 as an x.25 switch at one of our customer > place.Im > using X.21 DCE cable which is connected to NM-8A/S.And ach port is giving a > clock of 64K.to the device attached to this.This devices are MSC's(Mobile > switch's) and SUN machines with X.21 interface. > > This router has replaced traditional X.25 switch.All the parameters on the > ports are OK and the interface are coming up.If u see the config of 3640,on > port 2/2 one OMP machine(basically sun machine)which acts as a console is > connected.From this console,it makes X.25 calls to MSC switches i.e to all > other ports. > > Since i have configured router as a switch,from that console i should be > able > to make X.25 call to all of the port.But its not happening.Im just able to > make a call to one single interface whose route is the 1st route and the > other > x.25 calls to other ports are not happening.If u see the 1st route the > destination add. is 8888.So the 1st call happens successfully but second > call > to another add.i.e to another port is not happening.But if i remove that 1st > route and then try to make a call to 3333 which was a second route earlier > and > now the 1st one,the call establishes. > > Please suggest as to what should be added in x25 routing. > > The main intention is that from ,Console which is connected to se2/2 shoule > be > able to make x.25 call to all other ports. > > Config is attached. > > > > sh runn > Building configuration... > > Current configuration : 1910 bytes > ! > version 12.2 > service timestamps debug uptime > service timestamps log uptime > no service password-encryption > ! > hostname bp > ! > enable password cisco > ! > ip subnet-zero > ! > ! > ! > x25 routing > ! > ! > ! > interface Serial2/0 > description connected to HLR > no ip address > encapsulation x25 dce > x25 address 8888 > x25 htc 32 > x25 win 7 > x25 wout 7 > x25 idle 5 > x25 nvc 8 > clockrate 64000 > ! > interface Serial2/1 > description connected to CMISE1 > no ip address > encapsulation x25 dce > x25 address 4401 > x25 htc 32 > x25 win 7 > x25 wout 7 > x25 idle 5 > x25 nvc 8 > clockrate 64000 > ! > interface Serial2/2 > description connected to OMP10 > no ip address > encapsulation x25 dce > x25 address 2222 > x25 htc 32 > x25 win 7 > x25 wout 7 > x25 idle 5 > x25 nvc 8 > clockrate 64000 > ! > interface Serial2/3 > description connected to MSC1 > no ip address > encapsulation x25 dce > x25 address 3333 > x25 htc 32 > x25 win 7 > x25 wout 7 > x25 idle 5 > x25 nvc 8 > clockrate 64000 > ! > interface Serial2/4 > description connected to MSC2 > no ip address > encapsulation x25 dce > x25 address 3322 > x25 htc 32 > x25 win 7 > x25 wout 7 > x25 idle 5 > x25 nvc 8 > clockrate 64000 > ! > interface Serial2/5 > description connected to CMISE2 > no ip address > encapsulation x25 dce > x25 address 1122 > x25 htc 32 > x25 win 7 > x25 wout 7 > x25 idle 5 > x25 nvc 8 > clockrate 64000 > ! > Serial2/6 > no ip address > encapsulation x25 dce > x25 htc 32 > x25 win 7 > x25 wout 7 > x25 idle 5 > x25 nvc 8 > clockrate 64000 > ! > interface Serial2/7 > no ip address > encapsulation x25 dce > x25 htc 32 > x25 win 7 > x25 wout 7 > x25 idle 5 > x25 nvc 8 > clockrate 64000 > > x25 route 8888 source 2222 interface Serial2/2 > x25 route 3333 source 2222 interface Serial2/2 > x25 route 3322 source 2222 interface Serial2/2 > ! > line con 0 > line aux 0 > line vty 0 4 > password cisco > login > ! > > end > > Thanks and Regards, > ******* > Important > Confidentiality: This communication is intended for the above named person > and is confidential and/or legally privileged any opinion expressed in this > communication are not necessarily those of the Egyptian company for Mobile > Services (MobiNiL). If it has come to you in error you must take no action > based on it, nor must you copy or show it to anyone: please delete/destroy > and inform the sender immediately. > No Responsibility: MobiNiL is not responsible for any political, religious, > racial or partisan opinion in any correspondence conducted by its domain > users. Therefore, any such opinion expressed, whether explicitly or > implicitly, in any said correspondence is not to be interpreted as that of > MobiNiL. > Monitoring / Viruses: MobiNiL may monitor all incoming & outgoing e-mails in > line with current legislation. Although we have taken steps to ensure that > this e-mail and attachments are free from any Virus, we advise that in > keeping with good computing practice the recepient should ensure they are > actuallyvirus free. > The Egyptian Company for Mobile Services (MobiNiL) www.mobinil.com > > The World Trade Center: 1191 Corniche El Nil, Boulaq - Cairo - Egypt > Telephone: +20 2 574 - 7000 or + 20 12 320 - 0000 > Fax: +20 2 574 - 7111 or +20 12 320- 7111 > ******* Nirmal Datacomm Pvt. Ltd., Mumbai, India Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=56071&t=55369 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
