Robert, Aux could only work if you had configured the router before now to accept Aux connections.
The only posible solution is for you to go through the console port. Using a PC with a Terminal emulator set its parameters to: 9600 baud rate No parity 8 data bits 1 stop bit No flow control Using the appropraite console cable, connect the router to the PC, run the terminal software and set the parameters as suggested above. Then: 1. Switch off the Router 2. Press [Enter Key] to connect to the router (do not mind, you will not see anything displayed on the screen) 3. ON the router and type in the break sequence (depending on your terminal emulaion software and the OS you are running, your break sequence could be i.Ctrl+Break ii.Ctrl+F6+Break iii.Ctrl+a+f iv.Ctrl+b v.Ctrl+End vi. Break vii.control+shift+6+b etc!!! which ever works for you.) 4. Then on Rommon> Type "confreg 0X2142" ..To boot from flash. 5. On rommon > type "Reset" This makes the router to boot from flash and ignore its configurations. 6. Type "No" after the setup question of oress Ctrl+C 7. On Router> type "Enable" 8. On Router#type "copy startup-config running-config" 9. On Router# type "Config t" 0. On Router(config-t)# type "config-register 0x2102" 1. On Router(config-t)#type end 2. On Router# type "copy running-config startup-config With these you are set. If this work for you Bill, just send me a DEER for thanksgiving day, else please feel free to ask more questions. my 0.2 cents Regards Godswill Oletu --- dayo olabisi wrote: > Bill, > > telnet won't work if the router isn't up... I think > connecting via the Aux port may be of help. > > dayo > --- Creighton Bill-BCREIGH1 > wrote: > > I'm assuming you don't have VTY access - telnet, > of > > course, doesn't care > > about console port settings... > > > > Bill Creighton CCNP > > Senior System Engineer > > Motorola > > iDEN CNRC Packet Data / MPS > > > > > > > > -----Original Message----- > > From: Robert Massiache > > [mailto:[EMAIL PROTECTED]] > > Sent: Tuesday, November 19, 2002 3:27 PM > > To: [EMAIL PROTECTED] > > Subject: Re: Confreg problem...help! [7:57732] > > > > > > Thanks for the reply. > > > > The problem is upon boot up I am getting only > > garbled asci characters and > > the screen appears to be frozen. It don't let me > see > > anything and type > > anything to implement your suggestion...sorrry. I > > welcome if you could tell > > me some alternative...thanks a lot! > > > > thanks > > Robert M > > > > > > > > > > > > > > >From: "miken" > > >To: "Robert Massiache" , > > >CC: , > > >Subject: Re: Confreg problem...help! > > >Date: Tue, 19 Nov 2002 00:52:49 -0700 > > > > > >I believe the config-register is stored in NVRAM. > > So in theory, if you > > >bypass the startup config, you may default to the > > standard > > >config-register settings. Haven't tried it though > > to know for sure. > > >Have you tried booting into rommon(control-break > > sequence) and then > > >stepping through the confreg steps? > > > >http://www.cisco.com/en/US/partner/products/sw/iosswrel/ps1831/products > > >_comm > > > >and_summary_chapter09186a0080087baf.html#xtocid43127http://www.cisco.com/en > > / > > > >US/partner/products/sw/iosswrel/ps1831/products_command_summary_chapter0918 > > 6 > > >a0080087baf.html#xtocid43127HTH,Mike----- > Original > > Message ----- > > >From: "Robert Massiache" > > >To: > > >Cc: ; > > >Sent: Monday, November 18, 2002 7:39 PM > > >Subject: Confreg problem...help! > > > > > > > > > > Hi, > > > > I got a mc3810 router and was running perfect. > > Sometime ago I > > > > mistakenly typed a confreg value which I do > not > > remeber exactly but > > > > I know it was > > >not > > >a > > > > relevant one. I was actually practicing with > the > > confreg entries. > > > > > > > > What happened was that after I just rebooted > the > > router I lost the > > >console > > > > screen. I tried with all sorts of console port > > values like changing > > > > the baud-rate, start stop bit etc. > > > > > > > > I found it was responding to 1200 baud speed > but > > all I could find is > > >some > > > > corrupted and garbled ascii characters on the > > Teraterm. Same is the > > > > case with hyprterm. > > > > > > > > Any helpers please... > > > > > > > > thanks > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > _________________________________________________________________ > > > > Add photos to your e-mail with MSN 8. Get 2 > > months FREE*. > > > > > http://join.msn.com/?page=features/featuredemail > > > > > > > > > > > > > > > _________________________________________________________________ > > Protect your PC - get McAfee.com VirusScan Online > > > http://clinic.mcafee.com/clinic/ibuy/campaign.asp?cid=3963 > [EMAIL PROTECTED] > > > __________________________________________________ > Do you Yahoo!? > Yahoo! Web Hosting - Let the expert host your site > http://webhosting.yahoo.com [EMAIL PROTECTED] __________________________________________________ Do you Yahoo!? Yahoo! Web Hosting - Let the expert host your site http://webhosting.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=57808&t=57732 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
